Carrier Weathermaster 48P030-100 - Page 285

CL-7
CONTROLS SET POINT AND CONFIGURATION LOG (cont)
ITEM EXPANSION RANGE DEFAULT SETTING
COOL (cont) COOLING CONFIGURATION
DS.AP Dig Scroll Adjust Delta 0 to 100% 100
DS.AD Dig Scroll Adjust Delay 15 to 60 sec 20
DS.RP Dig Scroll Reduce Delta 0 to 100% 6
DS.RD Dig Scroll Reduce Delay 15 to 60 sec 30
DS.RO Dig Scroll Reduction OAT 70 to 120 dF 95
DS.MO Dig Scroll Max Only OAT 70 to 120 dF 105
MLV Min Load Valve Enable Enable/Disable Disable
H.SST Hi SST Alert Delay Time 5 to 30 min 10
RR.VF Rev Rotation Verified? Yes/No No
CS.HP Use CSBs for HPS detect? Yes/No Yes
EDT.R EVAP.DISCHRGE TEMP RESET
RS.CF EDT Reset Configuration 0 to 3 (multi-text strings) 2
RTIO Reset Ratio 0 to 10 3
LIMT Reset Limit 0 to 20 ^F 10
RES.S EDT 4-20 ma Reset Input Enable/Disable Disable
HEAT HEATING CONFIGURATION
HT.CF Heating Control Type 0 to 5 0
HT.SP Heating Supply Air Setpt 80 to 120 dF 85
OC.EN Occupied Heating Enabled Yes/No No
LAT.M MBB Sensor Heat Relocate Yes/No No
SG.CF STAGED HEAT CONFIGS
SG.CFHT.ST Staged Heat Type 0 to 5 0
SG.CFCAP.M Max Cap Change per Cycle 5 to 45 45
SG.CFM.R.DB S.Gas DB min.dF/PID Rate 0 to 5 0.5
SG.CFS.G.DB St.Gas Temp. Dead Band 0 to 5 ^F 2
SG.CFRISE Heat Rise dF/sec Clamp 0.05 to 0.2 0.06
SG.CFLAT.L LAT Limit Config 0 to 20 ^F 10
SG.CFLIM.M Limit Switch Monitoring? Yes/No Yes
SG.CF
SW.H.T Limit Switch High Temp 80 to 210 dF 170
SG.CFSW.L.T Limit Switch Low Temp 80 to 210 dF 160
SG.CFHT.P Heat Control Prop. Gain 0 to 1.5 1
SG.CFHT.D Heat Control Derv. Gain 0 to 1.5 1
SG.CFHT.TM Heat PID Rate Config 60 to 300 sec 90
HH.CF HYDRONIC HEAT CONFIGS
HH.CFHW.P Hydronic Ctl.Prop. Gain 0 to 1.5 1
HH.CFHW.I Hydronic Ctl.Integ. Gain 0 to 1.5 1
HH.CFHW.D Hydronic Ctl.Derv. Gain 0 to 1.5 1
HH.CFHW.TM Hydronic PID Rate Config 15 to 300 sec 90
HH.CFACT.C HYDR.HEAT ACTUATOR CFGS.
HH.CFACTCSN.1 Hydronic Ht.Serial Num.1 0 to 9999 0
HH.CFACTCSN.2 Hydronic Ht.Serial Num.2 0 to 6 0
HH.CFACTCSN.3 Hydronic Ht.Serial Num.3 0 to 9999 0
HH.CFACTCSN.4 Hydronic Ht.Serial Num.4 0 to 254 0
HH.CFACTCC.A.LM Hydr.Ht.Ctl.Ang.Lo Limit 0 to 90 85
SP SUPPLY STATIC PRESS.CFG.
SP.CF Static Pressure Config Enable/Disable Disable
SP.SV Staged Air Volume Control Enable/Disable Disable
SP.S Static Pressure Sensor Enable/Disable Disable
SP.LO Static Press. Low Range –10 to 0 in. wg 0

SP.HI Static Press. High Range 0 to 10 in. wg 5
SP.SP Static Pressure Setpoint 0 to 5 in. wg 1.5
SP.MN VFD Minimum Speed 0 to 100% 20
SP.MX VFD Maximum Speed 0 to 100% 100
HS.MN VFD MinSpeed in HeatMode 0 to 100 75
HS.MX VFD MaxSpeed in HeatMode 0 to 100 100
SP.FS VFD Fire Speed Over. 0 to 100% 100
SP.RS Stat. Pres. Reset Config 0 to 4 (multi-text strings) 0
SP.RT SP Reset Ratio 0.00 to 2.00 0.20
SP.LM SP Reset Limit 0.00 to 2.00 0.75
SP.EC SP Reset Econo Position 0 to 100% 5
S.PID STAT.PRESS.PID CONFIGS
S.PIDSP.TM Stat.Pres.PID Run Rate 5 to 120 sec 15
S.PIDSP.P Static Press. Prop. Gain 0 to 5 0.5
S.PIDSP.I Static Pressure Intg. Gain 0 to 2 0.5
S.PIDSP.D Static Pressure Derv. Gain 0 to 5 0.3