CashCode FrontLoad Series - Interface Connector Update Procedure; SOFTWARE UPDATE DIAGNOSTICS

Rev. 03-2004 Part 1. Operation Manual PAGE 1-49
FrontLoad Bill Validator Series - Operation and Service Manual
FOSUTATS
THGILCITSONGAID
NOITPIRCSEDRORRE GNILDNAH-TLUAF
NOHSALFNEERG1
DER
RORREecafretnilanretxE
domdaolnwoDTENCCnie
aolnwodTENCCrofelbatiussierawtfostahtyfireV.1.
d
.erudecorptaepeR.2
SEHSALFNEERG2
DERNO
CRCdraCyromeM
RORRE
nrut,niagakcitStramSehttresnidnaevomer,FFOREWOPnruT.1
NOREWOP.
.enow
enehthtiwdraCyromeMecalpeR.2
SEHSALFNEERG3
DERNO
yromeMniatadtcerrocnI
draC
.epytrotadilaVlliBehtotelbatiussierawtfosehttahtyfireV.1
.d
raCyromeMedoChsaCfoepyttcerroctresnI.2
SEHSALFNEERG4
DERNO
tonsidraCyromeM
detresni
.draCyromeMehttresniylreporP
SEHSALFNEERG5
DERNO
yromeMfoepytgnorW
draC
.draCyromeMedoChsaCfoepyttcerrocehttresnI
SEHSALFNEERG6
DERNO
daolnwodgniruderuliaF
nrut,niagadraCyromeMehttresnidnaevomer,FFOREWOPnruT.1
.NOREWOP
.
enowenehthtiwdraCyromeMecalpeR.2
SEHSALFNEERG7
DERNO
foRORREnoitarepO
ecafretnidraCyromeM
nrut,niagadraCyromeMehttresnidnaevomer,FFOREWOPn
ruT.1
.NOREWOP
.enowenehthtiwdraCyromeMecalpeR.2
Normally, the download process will be accompanied by a blinking red-green status light for about 1
minute. If the download has competed successfully, the status light will turn green. Should the down-
load be unsuccessful, the status light will turn red, but short green flashes of light will alternate with a
long red light (“green flashes on red”).
The following table lists possible errors which may take place during a download:
SOFTWARE UPDATE DIAGNOSTICS
Download procedure via interface connector:
In order to properly complete an interface download, the Memory Card must be present in the
Memory Card slot at all times – before and during the download.
1. When the FrontLoad Bill Validator has a CCNET protocol, the software download can be completed
via the host controller (refer to CCNET Protocol Description).
2. For a direct download via the interface connector, please follow the instructions below:
Step 1. Turn power OFF.
Step 2. Disconnect the interface connector from the Bill Validator.
Step 3. Remove the Validating Head from the Housing, and set Mode Switch to Service mode (see
page 36).
Step 4. Install the Validating Head into the Housing.
Step 5. Connect the CashCode Adaptor (see page 23 for exact type): a) to the Computer, b) to the
interface connector of the Bill Validator, and c) to the power outlet (AC 100-250V).
Step 6. From the computer, run the latest software version of the FL***.exe program.
Step 7. Follow the instructions displayed on the computer screen.
Step 8. After completing step 7, disconnect the CashCode Adaptor: a) from the power outlet, b) from
the Bill Validator, and c) from the Computer.
Step 9. Remove the Validating Head from the Housing, and set Mode Switch to Validation mode (see
page 36).
Step 10. Install the Validating Head into the Housing.
Step 11. Connect the interface connector to the Bill Validator.
Step 12. Turn power ON.