Casio SE-S10 - Setting Tax Rate and Rounding

Part-2
27
E
Part-2 CONVENIENT OPERATION
1-9 Setting the Tax Rate
and rounding
P3 appears in mode display
ProgramsetcodeNo.fortaxrate1*
1
•Youcanuseeitheran
add-onratetaxoran
add-inratetax(VAT),
depending on the
requirements in your
area.Youcanspecify
only one tax rate.
•Thenormalrounding
specicationtellsthe
cashregisterhowto
round tax amounts to
thepropernumberof
decimalplaces.
•Thespecialround-
ingspecicationand
Danish rounding tell
thecashregisterhow
toroundoffsubtotals
and totals so that their
rightmost 2 digits are
00and50.
•Notethattheround-
ingspecicationyou
programforyourcash
register depends on
thetaxlawsofyour
country.
C
?ZXB
??"???? p
???? p
SelectnumbersfromlistB
SelectnumberfromlistC
SelectnumberfromlistD
(To end the setting)
*
1
 Programsetcode
No.forTaxrate2is
?XXB
Tax rate 3 is
?CXB
Tax rate 4 is
?VXB
.
EntertaxrateA
Tax rate specifications
Thetaxratewithintherangeof0.0001~
99.9999%.Use
"
keyfordecimalpoint.
A
Normal rounding specifications
Cutoffto2decimalplaces.
(1.544=1.54;1.545=1.54)
??
B
Roundoffto2decimalplaces.
(1.544=1.54; 1.545=1.55)
B?
Roundupto2decimalplaces.
(1.544=1.55; 1.545=1.55)
>?
Special rounding specifications for subtotal and total amounts
Nospecications
?
C
Specialrounding1:0~2
➝
0; 3~7
➝
5; 8~9
➝
10
Examples:1.21=1.20;1.26=1.25;1.28=1.30
Z
Specialrounding2:0~4
➝
0; 5~9
➝
10
Examples:1.123=1.120;1.525=1.530
X
Danish rounding
*2
: 0~24
➝
0;25~74
➝
50;75~100
➝
100
(settheamounttenderrestrictiononpage23also)
Examples:1.11=1.00;1.39=1.50;1.99=2.00
C
Malaysianrounding:0~2
➝
0; 3~7
➝
5; 8~9
➝
10
(settheamounttenderrestrictiononpage23also)
Examples:1.21=1.20;1.26=1.25;1.28=1.30
B
Scandinavianrounding:
0~24
➝
0;25~74
➝
50;75~99
➝
100
Examples:1.21=1.00;1.30=1.50;1.87=2.00
N
Australianrounding(onlyfortaxrate1)
0~2
➝
0; 3~7
➝
5; 8~9
➝
10
Examples:1.21=1.20;1.26=1.25;1.28=1.30
M
Czechrounding:0~49
➝
00;
50~99
➝
100
Examples:1.23=1.00;1.52=2.00
<
Normal rounding specifications
Nospecications.
?
D
Speciesadd-onratetax.
X
Speciesadd-inratetax(VAT).
C
Seepage20(departmentkey),21(percentkey),22(minuskey)tochangethexedtaxstatus.
*2:IncaseofdeningDanishrounding,theEuroshouldbesettothesubcurrencyandthelocalto
themaincurrency.