Cedima CF 13.3 B - Page 13

Basic safety instructions
13
• CEDIMA® • Technical Documentation • All rights reserved according to ISO 16016 • Changes serving technical progress reserved •
ENGLISH
3.5.2 Commissioning
• During start-up and shut-down procedures always watch
the indicators in accordance with the operating manual.
• Before you start up the machine or set it to motion, make
sure that the starting or running machine does not cre-
ate any hazard to other persons’ health.
• Start the machine exclusively from the engine control lo-
cation (CF•13.3 B/CF•13.3 B-L, rear right at the machine).
• Operate the machine exclusively from the control loca-
tion (CF•13.3 B/CF•13.3 B-L, behind the machine).
• The driver/ operator position is only to be lled by the
user. Keep third parties away from the machine.
• It must be ensured that the operator has constantly suf-
ciently view on the work area and that he can intervene
at any time in the working process.
• Water hoses must be laid in such a way that damage by
crossing or by the tool cannot occur.
• The cutting operation must be performed using the wet
cutting method in order to prevent the formation of
hazardous clouds of ne dust and to increase the service
life of the cutting tool.
• When using the wet-cutting method, always make sure
that there is enough water at the proper
places. Make sure there is enough cooling water at the
cutting groove.
• When working is the dry-cutting method, make sure
there is enough suction to remove the dust.
• If harmful or explosive substances can emerge during
the work, e.g. dust, slurry, the national health- and safety
rules apply.
• Moving the machine outside the workplace is only al-
lowed without saw blade.
• When operating the machine on public roads, ways and
places always observe the trac regulations in force and,
if necessary, make sure beforehand that the machine
complies with the relevant road vehicle regulations.
• Always control the accident-proof accommodation of
the accessories before the transport of the machine.
• Avoid any operation that might aect the stability of
the machine. Always keep a sucient distance from the
edges of excavations, ditches and slopes.
• Never travel across slopes exceeding 5%.
• Always use safety ropes when operating the machine on
sloping terrain exceeding 15%.
• Before leaving the machine always secure it against inad-
vertent movement (rolling o) and accidental restart
(unauthorized use).
3.5.3 Special work related to the
maintenance and repair of the
machine and troubleshooting,
disposal
• Observe the adjustment, maintenance and inspection
activities and intervals set out in the operating manuals,
including information on the replacement of parts or
assemblies.
• Brief the operating personnel before initiating special
repair or maintenance activities. Appoint a person to
supervise such activities.
• In any work concerning the operation, adaptation to
production requirements, conversion or adjustment
of the machine and its safety-oriented devices or any
work related to inspection, maintenance and repair,
always observe the start-up and shut-down procedures
described in the operating manual as well as the instruc-
tions on maintenance activities.
• If necessary, secure a large area around the location
where maintenance of the machine is to be performed.
• Maintenance and repair work may be carried out only
if the machine is placed on level and solid ground and
secured against inadvertent movement.
• If the machine is completely shut down for maintenance
or repair work, it must be secured against inadvertent
restarting:
- remove the key and/or disconnect the power supply,
- attach a warning sign at the main switch.
• When using a lifting gear for replacing individual parts
or large assemblies make sure that the parts/assemblies
are carefully attached to the lifting gear and secured in
place to avoid hazardous conditions. Use only suitable
and technically perfect lifting gear and suspension sys-
tems with adequate lifting capacity. Never work or stand
under suspended loads.
• The fastening of loads and the instructing of crane/
industrial truck operators should be entrusted to experi-
enced persons only. The instructor must be within sight
or sound of the operator.
• Before performing any maintenance/repair activi-
ties clean the machine, especially the connectors and
screwed joints, and remove any oil, dirt and preservative
agents. Never use aggressive detergents. Use lint-free
cleaning rags.
• Before cleaning the machine with water or other clean-
ing agents cover or tape up all openings which -for
safety and functional reasons- must be protected against
the ingress of water/steam/cleaning agents. Special care
must be taken with bearings, electric motors and elec-
tronic systems. Pay attention to the protection classes.
After cleaning, remove the covers/tapes completely.