Cello READY 4i - Leak Test; Leak Testing Procedure; USING THE BARBECUE; Ignition with Piezo Igniter

Leak test
Ignition by battery operated piezo- igniter
Lighting by match in case of piezo igniter
failure
USING THE BARBECUE
Always check the following when
carrying out a leak test
Carry out leak testing as follows
Leak testing is always required in the following cases:
š%HIRUHıUVWWLPHLJQLWLRQRIWKHEDUEHFXH
š(YHU\WLPHDQHZJDVF\OLQGHULVLQVWDOOHGRUVRPH
component replaced.
š:HUHFRPPHQGSHUIRUPLQJWKHWHVWDWOHDVWRQFHD
year, before every barbecue season.
Always carry out the leak test outdoors, away from
heat, open flame, and combustible liquids. Do not
smoke while performing the test. Always use 50/50
liquid soap/water solution for leak testing. Never use
a match or open flame.
š*DVF\OLQGHUYDOYHVDQGF\OLQGHUWKUHDG
š$OOJDVF\OLQGHUZHOGV
š5HJXODWRUPRXQWLQJDQGJDVF\OLQGHUFRQQHFWLRQV
š$OOKRVHMRLQWVLQFOXGLQJVLGHEXUQHUKRVHVLI
present).
š 8VH D UHFHQWO\ ıOOHG DQG FKHFNHG JDV F\OLQGHU
connected to the barbecue with all of the barbecue
connectors in the OFF position.
š2SHQWKHSUHVVXUHUHJXODWRU
š8VLQJDEUXVKDQGVRDSZDWHUVROXWLRQZHWDOORI
the connections and components.
š&KHFNFDUHIXOO\IRUEXEEOHVVLJQVRIJDVOHDNDJH
š,IEXEEOHVDSSHDUQH[WWRFRQQHFWLRQVWLJKWHQWKH
connections until retesting shows no sign of leakage
(always turn o gas supply for the duration of leakage
repairs).
š&ORVHWKH SUHVVXUHUHJXODWRU DQG PDNHVXUH WKH
control valves are closed.
Do not use the barbecue if you fail to eliminate a leak.
Close the gas cylinder valve, detach the gas cylinder
and contact the importer.
If the burner does not ignite in 10 seconds in spite of
repeated attempts, turn o the barbecue controller
and cut gas supply from the cylinder. Leave the lid
open and wait for at least 5 minutes before
re-attempting to light the barbecue. This way, the gas
accumulated in the barbecue can escape.
1. Always open the barbecue lid before igniting a
burner.
2. Turn on gas supply from the cylinder and low-
pressure regulator.
3. Press control knob to bottom and turn it
anticlockwise till position.
4. Push ignition button until burner ignites.
5. Adjust the burner flame by turning the
controller between high and low power.
6. After the burner has ignited, the rest of the
burners can be ignited by turning the corresponding
control knobs counter- clockwise.
If burner does not ignite, see troubleshooting table, or
ignite with long match.
Grill firebox’s right side has open hole, where grill can
be ignited with long match.
1. Always open the lid before lighting the barbecue.
2. Turn on gas supply from the cylinder and low-
pressure regulator.
3. Though firebox’s open hole place a burning match
next to the burner.
4. Push and turn right side control knob till posi-
tion. Make sure by looking through the grid and heat
distribution panel that the burner has definitely
ignited.
If the burner still does not ignite, see the trouble-
shooting table for help.
Warning! Never lean over the barbecue when lighting
or using it.
4