17
KIT COMFORT
9. The Comfort Kit comprises 2 padded shoulder straps and
a padded crotch strap (Fig. 9). The shoulder straps are
tied together by a ribbon with a snap fastener.
HOW TO ADJUST THE LEGREST
10. The legrest has two positions. To adjust it, use the cen-
tral lever located under the legrest (Fig. 10).
CANOPY
11. The stroller is equipped with a sun canopy and wind-
shield that can be adjusted to various positions.
To adjust the hood, pull and/or push it centrally. For more
extensive protection, open the zipper on the hood and
open the remaining fabric section (Fig. 11). Raising the fab-
ric ap present on the top section of the hood (Fig. 11A) re-
veals a mesh section that can be used to observe the child.
HANDLE ADJUSTMENT
The stroller features a handle that can be adjusted in height,
according to the user’s needs.
12. Press the button in the centre of the handle (Fig. 12)
and pull the handle towards you to the desired position.
Starting from the lowest or closed position, the handle
can be adjusted to dierent positions (Fig. 12A).
After switching from one position to the other, make sure
the automatic locking mechanism is properly engaged.
PARKING BRAKE
13. The parking brake acts on both stroller's rear wheels
at the same time. To activate the brake push the lever
down (Fig. 13). To deactivate the brake, operate the lever
in the other direction.
WARNING: Always apply the brakes whenever the stroller
is stopped. Never leave the stroller on a sloped surface, with
a child inside, even with the parking brakes engaged.
WARNING: After operating the brake lever, ensure that
the brakes are correctly engaged in both of the rear wheel
units.
SWIVEL WHEELS
The stroller has front swivel/xed wheels. It is recommend-
ed to use the wheels in the xed mode on particularly
changeable surfaces. The use of the wheels in the swivel
mode is recommended in order to increase the control of
the stroller on a normal road surface.
14. To lock the front wheels in swivel mode, push down on
the lever located on the rear part of the wheels; to un-
lock them, push the lever upwards (Fig. 14).
Ensure that both front wheels are xed or in swivel mode.
FOLDING THE STROLLER
WARNING: When opening or closing the stroller, make
sure that your child or other children are at a safe distance.
Make sure that during these operations the moving parts of
the stroller do not come into contact with your child.
WARNING: You must remove all contents from the basket
before closing the stroller.
15. The stroller can be folded either without the seat or with
the seat (in either conguration: forward facing or rear-
ward facing).
To close the stroller, adjust the height of the handle to the
lowest, closed position.
Press the button and, at the same time, raise the backrest
adjustment lever by pushing the backrest forward (Fig. 15).
The stroller will close itself automatically (Fig. 15A).
To reopen the stroller, lift the handle until a click conrms
that it has opened (Fig. 15B), install the seat as indicated in
step 5 if previously removed, taking care to lift the bumper
bar as shown in gure 15C.
In case of closing the frame without the seat, it is necessary
to push down the levers on the joints (Fig. 15D), the stroller
will fold at this point.
CARRY-ALL BASKET
16. To remove the basket from the frame of the stroller, un-
lock the 3 plastic hooks on each side (Fig. 16 and 16A)
and the snap fasteners. To act on the plastic hooks sewn
to the side elastic of the basket, it is suggested to per-
form the operation with the frame semi-closed. Detach
the Velcro straps under the footplate (Fig. 16B), and
those on both sides of the rear tube (Fig. 16C).
To assemble the basket, carry out the operations in reverse
order, taking care to fasten the hooks of the side elastic
bands onto the metal pins (Fig. 16D).
REMOVING THE LINING OF THE HOOD
17. If the fabric needs to be removed from the hood for
cleaning, follow these steps: Open the snap fasteners
on the joints of the hood and then all those on the pe-
rimeter of the backrest (Fig.17).
Use a pointed object to slightly lift the plastic retainers of
the joints (Fig. 17A) and pull the metal rod of the hood up-
wards; Pull the rod out of the fabric.
To reassemble the fabric and the hood carry out the opera-
tions in reverse order.
WARNING: The hood must be xed on both sides of the
stroller. Ensure that the canopy is correctly fastened.
REMOVING SEAT LINING
18. To easily remove the fabric from the seat, detach the
seat from the frame (paragraph 5) and remove the
bumper bar (paragraph 6).
After unfastening the hood (paragraph 17), open the zip at
the bottom of the backrest (Fig. 18), release the snap fas-
teners located under both sides of the seat (Fig. 18A) and
under the legrest (Fig. 18B); remove the crotch strap with
buckle from the frame by passing the ribbon through the
slot in the metal ring (Fig. 18C) and remove the fabric from
the legrest (Fig. 18D).
Detach the Velcro straps located on the inside of the joints
of the hood (Fig. 18E) and remove the fabric from the joints
(g. 18F) complete the operation by releasing the fabric
from the backrest adjustment lever (Fig. 18G) and pull it
upwards (Fig. 18H).
After removing the fabric from the frame, the four belts
can be pulled out by passing them through the slots, as
described in point 8.
The fabric is now released, the panel must be removed
from the backrest by opening the Velcro at the bottom of
the panel (Fig. 18I)
To t the lining on the seat, follow these same steps in the
reverse order; During this operation it is necessary to re-at-
tach the legstrap to the tube (Fig.18C), the waist straps at
the bottom of the backrest (Fig. 8A - no.4) and the shoulder
straps in the top part of the backrest (Fig. 8A - no.1/2/3).
To Next Page
Loading...
