21
pressing the centre button and raising the handle (diag. 2B);
now open the stroller by using your other hand to push the
front section of the frame downwards, until you hear it click
into place (diag. 2C).
Make sure the stroller is open properly before proceeding any
further.
3. The rear seat on the stroller is tted with a footrest. Once
the stroller is open, lower the footrest (diag. 3).
4. To adjust the height of the handlebar, press the two side
buttons (diag. 4) at the same time and move the handlebar to
the required position.
BASKET
5. The stroller comes with a practical carry-all basket. To
assemble the basket, slide the U-shaped tube into the tube
ends on the back of the stroller, as seen in diag. 5A. The
U-shaped tube is tted correctly when you see the 2 grey rods
on the bottom, protruding from the holes below the stroller
frame tubes and you hear them click into place.
To finish, fasten the fabric to the tube using the press studs
(diag. 5B). Never use the carry-all basket without the supports
inserted properly. Always remove all contents from the basket
before you close the stroller.
6. You can also open the zip (diag. 6) on the back of the basket
to access it more easily.
FITTING THE BACK WHEELS
7. Parts needed to t the back wheels: see diag. 7.
8. Remove the caps from the ends of the rear axle, then slot
the rear axle onto the frame, until you hear it click into place
(diag. 8).
WARNING: always check the rear axle is tted properly before
using the stroller.
9. To assemble the wheels on the rear axle A) follow the
instructions in the correct order (see diag. 9A):
- the wheel B)
- the washer C)
- the spring pin D)
- the cap E)
Make sure you insert the fastening spring pin as indicated in the
diagram: the at side must be inserted in the whole on the axle,
whilst the closed end of the spring pin must be facing outwards
(diag. 9B). Repeat the operation to assemble the other wheel,
following the instructions in the same order.
FITTING THE FRONT WHEELS
10. Slot the front wheel block onto the stroller frame as seen in
diag. 10, until you hear it click into place. Repeat this procedure
for the other wheel block.
WARNING: before use, make sure the wheel locks are properly
secured, by pulling them rmly.
BUMPER BAR
11. To assemble the bumper bar, simply slot it into the two
holes on the ends of the front armrests, as seen in diag. 11.
12. To remove the bumper bar, press the two buttons found
under the armrests, and pull the bar towards you (diag. 12).
WARNING: Always fasten your child with the safety belts. The
bar IS NOT a device for containing your child.
WARNING: Never use the bumper bar to lift the stroller up
with the child sitting in it.
HOOD
The stroller comes with two hoods.
13. To assemble the front hood, connect the hood fastener to
the guides on the armrests (diag. 13). Repeat the operation to
fasten it to the other side of the stroller.
14. To assemble the rear hood, connect the hood fastener to
the round stopper on the rear stroller tube (diag. 14). Repeat
the operation to fasten it to the other side of the stroller.
15. How to open the hoods: open the hood as illustrated in
g. 15A and press the two side snap-bars down to lock it in
place (diag. 15B). Warning: always release these two snap-bars
before trying to close the hood.
USING THE SAFETY HARNESS
Each seat is tted with a ve-point safety harness which
consists of two shoulder straps, a lap belt and a crotch strap
with a buckle. WARNING: when carrying children from 0 to 6
months of age, the shoulder straps must be threaded through
the adjuster slots before being fastened.
16. Thread the safety clasps through the fabric loops (diag.
16A) and check that the shoulder straps are fitted at the right
height for the child: if this is not the case, adjust the height
as necessary (diag. 16B). You can also use the padded strap
covers by sliding them onto the straps (diag. 16C).
17. Place the child inside the seat, connect the safety clasps to
the 2 toothed ends, and insert the 2 toothed ends into the buckle
(diag. 17). Now use the clasps to adjust the length of the lap belt.
18. For extra safety, the stroller is tted with D-rings which
can be used to t a separate safety harness, compliant with BS
6684 Standards. The rings are tted internally on the right and
left side of the stroller seat, as seen in diagram 18.
19. To release the lap belt, press the two toothed ends together
at the same time (diagram 19).
WARNING: the safety harness must always be fastened to
guarantee safety for your child.
WARNING: the safety harness must always be used with the
crotch strap to guarantee safety for your child.
ADJUSTING THE FRONT SEAT BACKREST
20. To release the recliner mechanism on the front seat
backrest: use your thumb to press button A and then slide it to
the left whilst pulling the handle upwards (diag.20).
21. Now push the backrest backwards (Diag. 21). To raise the
backrest, simply lift it to the desired position, without pressing
on the handle.
The front seat backrest can also be adjusted forwards, so the
stroller can be used with the child car seat (see the “USING
THE CHILD CAR SEAT” section).
ADJUSTING THE REAR SEAT BACKREST
22. To recline the rear seat backrest, lift the adjuster handle on
the back of the backrest and pull it downwards (diag. 22). To
raise the backrest, simply lift it to the desired position, without
pressing on the handle.
WARNING: these operations can become more difcult when
the child is sat in the seat.
REAR BRAKES
The rear wheels are tted with a twin-braking system which allows
you to use just one foot pedal to control both the rear wheels.
23. To apply the brakes, press one of the two levers on the rear
wheels downwards, as illustrated in diagram 23.
24. . To release the brakes, press one of the two levers on the
rear wheels upwards, as illustrated in diagram 24.
WARNING: Always apply the brakes whenever the stroller is
stationary.
WARNING: Never leave the stroller on a sloping surface with a
child inside, even with the brakes applied.
WARNING: after applying the brake lever, check that the
brakes are locked in place on both rear wheels.
SWIVEL WHEELS
The front wheels on this stroller can be used in xed or swivel mode.
25. To use the wheels in swivel mode, lift the lever tted
between the two wheels. Use the swivel wheels on smooth
surfaces. To use the wheels in xed mode, press the lever
downwards again (diag. 25).
WARNING: the swivel wheels make the stroller easier to
manoeuvre; it is however recommended to use the wheels in
xed mode on uneven ground to guarantee better stability (on
gravel, unpaved roads etc.)
WARNING: Both wheels must be switched to swivel or xed
mode at the same time.
CLOSING THE STROLLER
WARNING: when closing the stroller, make sure that your child
and all other children are at a safe distance.
Ensure that during these operations the moving parts of the
stroller do not come into contact with your child.
26. To close the stroller, start by switching the swivel wheels
to the xed wheel position. Move the sliding bar on the tray to
the left (diag. 2A) whilst pressing the centre button and raising
the handlebar (diag. 2B). Now close the stroller by pressing the
centre of the carry-all basket downwards with one foot (diag.
26).
27. When the stroller is closed and locked in place, it will stand
up on its own (diag. 27).
USING THE CHILD CAR SEAT
The stroller is tted with clasps so you can use two KEYFIT child
car seats without the need for additional fastening devices.
WARNING: When using the child car seat, please read the
relative instruction manual carefully.
WARNING: only CHICCO KEYFIT child car seats can be hooked
onto the stroller.
Improper use of this stroller with an incompatible child car seat
can cause serious injuries to children.
WARNING: Before using the stroller in combination with
the child car seat, always check that the hook-on system is
correctly closed and locked in place.
WARNING: Children must always be strapped into the child
car seat using the safety harness.
INSTALLING THE CHILD CAR SEAT ON THE FRONT SEAT
OF THE STROLLER
28. Remove the bumper bar and adjust the front seat backrest
forwards, following the instructions provided in paragraph
20 to release the backrest recliner mechanism and push it
forwards (diag.28).
29. Open the Velcro on the aps so that the side anchor points
are visible (diag. 29).
30. Now position the child car seat inside the stroller seat
aligned with the side anchor points. The child car seat will then
automatically click into place (diag 30). Try pulling the child
car seat upwards to check that it is tted correctly.
WARNING: When you remove the child car seat, remember to
To Next Page
Loading...
