Christie Matrix StIM-WQ - User Manual

144 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Matrix StIM

™

WQ/SIM WQ

User Manual

020-100883-01

Table of Contents

Default Chapter7
- Table of Contents7
Safety Warnings and Cautions13
Projector Overview14
- Key Features14
List of Components15
Purchase Record and Service Contacts15
Installation Considerations17
Installation Procedures18
- Unpack the Projector18
- Mount the Projector19
- Mount a Ruggedized Kit (Optional)19
- Install the Lens20
Setup Procedures21
- Adjust Lens Focus21
- Calculate Throw Distance and Position22
- Determine Vertical and Horizontal Position23
- Connect a Source24
- Connect to Power26
- Disconnect Power26
- Network Setup for External Communications27
- Arrayloc Network Configuration31
  - Arrayloc over Control Network31
  - Arrayloc over Arrayloc Network (Preferred)32
- Adjust Image Geometry and Optical Alignment33
  - Basic Optical Alignment33
  - Folded Optics33
- Boresight Alignment34
- Adjust Software to Optimize Image35
Login to Webui37
Navigate the Webui38
- The Global Icon39
- Slidebars in Menus39
- Check Boxes39
- Drop-Down Lists39
- Help Text40
Basic Webui Operation41
- Main Tab - General41
- Main Tab - Status41
- Tools Tab - Virtual OSD42
- Admin Tab43
- Admin Tab - Users45
- Advanced Tab - Real Time Events (RTE)46
- Advanced Tab - Serial48
Using the IR Remote49
- Wired Remote49
- IR Remote Commands50
Select Inputs52
Working with Infrargb53
- Basic Infrargb Setup53
- Select Lighting Mode54
- Set RGB and IR Lighting Mode54
- Manage Infrargb with IRLOC55
  - Adjust Infrargb Across the Array from the Master Projector55
  - Adjust Infrargb to Individual Projectors55
- Setup Source Sequence56
- Select a Lighting Mode59
- Adjust Light Mode Brightness Levels59
Reduce Motion Artifacts60
Arrayloc61
- Take Control of the Array61
- Configure Bright/Colorloc63
- Adjust Projected White and Primary Colors for the Array64
- Fine-Tune Whites, White Brightness, or Primary Colors66
- Configure Arrayloc67
- Fine-Tune Projector Colors with a Color Meter68
Image Settings69
- Adjust Gamma Settings69
Configure the Display71
- Output Options71
- Power Management72
- Change Date and Time73
- Communications73
- Diagnostics and Calibration76
Upgrade Software78
- Requirements78
Troubleshooting Guidelines81
System Warnings and Errors81
Status Display82
Error Codes83
General Maintenance85
- Cleaning the Lens85
  - Remove Dust85
  - Remove Fingerprints, Smudges, or Oil85
Webui Menu Tree87
Serial Communication89
- Connection and Use89
- Message Formats89
- Basic Message Structure90
- Sample Messages and Their Meaning93
- What Is Actually Sent in a Message94
- Maximize Message Integrity95
- Access Specific Inputs96
- Flow Control96
- Network Operation97
- Description of Control Types98
Serial Command Reference99
- Array Bright Color LOC (ABL)99
- Auto Color Enable (ACE)101
- Accuframe (ACF)102
- Address (ADR)102
- Active Projector (APJ)103
- Auto Power up (APW)103
- Auto Shutdown (ASH)104
- Baud Rate (BDR)104
- Base Gamma Curve (BGC)105
- Base Gamma Function (BGF)105
- Base Gamma Slope (BGS)106
- Broadcast Key Mode (BKY)106
- Color Enable (CLE)107
- Data Logging (DLG)107
- Error Message Enable (EME)108
- Enable Stealth Mode (ESM)108
- Fan Assist (FAS)109
- Frame Lock Enable (FLE)109
- Serial Flow Control (FLW)110
- Frame Delay (FRD)110
- Gamma Correction (GAM)111
- General Purpose Input/Output (GIO)111
- Serial Help (HLP)112
- Projector Health (HLT)112
- Infrargb (IFS)113
- Infrargb Coefficient (IRC)115
- IRLOC Configuration (IRL)116
- Test Pattern Grey (ITG)117
- Internal Test Pattern (ITP)117
- Keypad IR Sensor Disable (KEN)118
- Local Setting (LOC)118
- Logical Shutter (LSH)119
- Serial Mode (MDE)119
- Network Setup (NET)120
- Network Routing (NTR)121
- Projector Color Adjustment (PCA)122
- Projector Hours (PJH)123
- Ping (Png)124
- Swap (PPS)124
- Serial Port (PRT)124
- Power (PWR)125
- Advanced Color Setting (RGB)126
- Real Time Events (RTE)127
- Select Input (SIN)129
- Screen Orientation (SOR)130
- System Status (SST)130
- Target Color Space (TCS)131
- Time/Date (TMD)132
- Test Pattern Enable (TPE)132
- Target White Point (TWP)133
- User ID (UID)134
GPIO Port135
- Configure GPIO136
Rs-422139
Matrix Stim™ WQ/SIM WQ Specifications139

Need help?

Do you have a question about the Christie Matrix StIM-WQ and is the answer not in the manual?

Christie Matrix StIM-WQ Specifications

General

Brand	Christie
Model	Matrix StIM-WQ
Category	Projector
Language	English

Related product manuals

Christie WX10K-M

Preview: Christie M Series

Christie M Series

Christie HD14K-M2

Preview: Christie CP2000-M

Christie CP2000-M

Christie Mirage HD25

Preview: Christie M RGB Series

Christie M RGB Series

Christie Mirage S+14K

Christie Mirage Series

Christie Roadster HD10K-M

Christie Roadster HD14K-M

Christie Mirage HD10K-M Runco

Preview: Christie LW400