Cisco Catalyst IR1800 Rugged Series

To Next Page

To Previous Page

If no antenna cables are being installed on a port, make sure the caps are installed on the unused

connector.

Note

Cisco Catalyst IR1800 Rugged Series Router Hardware Installation Guide

Pluggable Interface Modules

Installing a PIM

Main Page

Table of Contents3
Preface9
Objective9
Audience9
Conventions10
Safety Warnings10
Related Documentation16
Searching Cisco Documents17
Product Overview19
Overview of Features19
Cisco IR1800 Series Platform Features20
Cisco IR1821 Router20
Cisco IR1831 Router21
Cisco IR1833 Router21
Cisco IR1835 Router21
Front Panel Overview21
Rear Panel Overview22
Pluggable Modules23
Cellular Pluggable Interface Module (PIM)23
SSD Module23
GPS Module23
SFP Modules23
Wireless Interface Module (WIM)25
Gigabit Ethernet Combo Port25
Gigabit Ethernet Copper Ports25
Power over Ethernet25
Front Panel Leds25
Reset Button27
Supported Cisco Antennas and Antenna Accessories27
Modem Support27
Power Supply29
Serial Ports29
USB Ports30
Installing the Router31
Overview31
Safety Information31
Equipment, Tools, and Connections32
Items Shipped with Your Router32
Additional Items32
Installing the Router33
Mounting on a Wall, Table, or Other Flat Surface33
Installing a DIN Rail35
Mounting the DIN Rail Bracket on the Router (Horizontal)36
Attaching the Bracket to the DIN Rail36
Changing the Bracket Orientation38
Bracket Disassembly39
Bracket Reassembly41
Mounting the DIN Rail Bracket on the Router (Vertical)42
Installing the Router Ground Connection43
Antenna Selection and Installation45
Introduction to Selecting Antennas45
Antenna Installation Best Practices45
Supported Antennas for the IR1800 Series Router47
Pluggable Interface Modules48
Wi Fi Modules48
Indoor Antennas48
Outdoor Antennas49
Outdoor and Transportation Antennas50
Supported Extension Bases and Cables50
Pluggable Interface Modules51
Introduction to Installing Pluggable Interface Modules51
Installing a PIM52
Sub-6 Ghz Pluggable Interface Module57
Sub-6 Ghz Support on Iot Routing57
Pluggable Interface Module Overview58
LED Behaviors59
RF Band and Port Mapping for the P-5GS6-GL Antenna60
Thermal Mitigation61
Attaching an Antenna63
Cisco Wi-Fi Interface Module (WIM)65
Overview65
Installation67
Transmit Power and Receive Sensitivity69
Thermal Mitigation72
SSD Module73
Introduction to the Solid State Drive in the IR1800 Series73
Installing an SSD Module74
GPS Field Replaceable Unit Module77
Overview of the GPS FRU Module77
Installation and Removal of a GPS FRU Module78
Digital I/O, Ignition, and CAN Bus Connectivity81
Overview of the Digital I/O, Ignition, and CAN Bus Connectivity81
Digital I/O Features81
The Digital I/O Connector81
Digital I/O Specifications83
Controller Area Network Bus Features83
Can Bus Power Connector84
On-Board Diagnostic (OBD-II)84
Connecting the Router87
Overview of the IR1800 Connecting Process87
Preparing to Connect the Router87
Preventing Damage to the Router87
Connecting a PC, Server, or Workstation88
Connecting a PC to the Console Port88
Connecting to DC Power and CAN Bus Wiring89
Plugs and Pinouts89
Verifying Connections90
Installing the IP54 Kit91
Overview of the IP54 Kit91
Installing the IP54 Kit93
Installing the Front Cover93
Technical Specifications97
Overview of Technical Specifications for IR1800 Series Routers97
Router Specifications97
Regulatory Compliance99
Related Documentation99
Installation Warning and Caution Statements100
Hazardous Locations Standards and Marking Strings101
EMC Information102
Class a Notice for FCC102
Industry Canada102
Canadian Compliance Statement102
European Community, Switzerland, Norway, Iceland, and Liechtenstein103
Declaration of Conformity with Regard to R-ED Directive 2014/53/EU103
Declaration of Conformity for RF Exposure104
RF Exposure104
This Device Meets International Guidelines for Exposure to Radio Waves104
This Device Meets FCC Guidelines for Exposure to Radio Waves105
FCC Radiation Exposure Statement105
This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves106
ISED Radiation Exposure Statement106
Additional Information on RF Exposure106
EMC Class a Notices and Warnings107
Declaration of Conformity with Regard to EU Directive 2014/53/EU107
National Restrictions109
Denmark109
Italy109
Latvia110
Taiwan110
Statement 191-Voluntary Control Council for Interference (VCCI) Class a Warning for Japan110
Statement 191 Voluntary Control Council for Interference (VCCI) Class a Warning for Japan110
ステートメント 191-日本向け VCCI クラス a に関する警告110
Statement 1008-Class 1 Laser Product111
Statement 1008 Class 1 Laser Product111
ステートメント 1008-クラス 1 レーザー製品111
Statement 1051-Laser Radiation111
Statement 1051 Laser Radiation111
ステートメント 1051：レーザー放射111
Statement 1255-Laser Compliance Statement111
Statement 1255 Laser Compliance Statement111
聲明4011-國家通信委員會警告112
Intended Use of Equipment112
Changing Output Power112
Obtaining Documents from Cisco.com112

Cisco Catalyst IR1800 Rugged Series - Page 56

Table of Contents

Other manuals for Cisco Catalyst IR1800 Rugged Series

Related product manuals