EasyManuals Logo

Cisco WAP125 User Manual

Cisco WAP125
13 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
Cisco WAP125 Quick Start Guide 3
WAP125 to network devices, such as computers, routers, or switches. We strongly
recommend that you use a Category 5e or better cable for Gigabit connectivity.
POWER—The POWER button is used to turn the power on and off. It is not
applicable when using PoE.
12V DC—The 12V DC jack is used to connect the supplied power adapter to the
Cisco WAP125 if you are not using PoE.
Kensington Lock SlotThe Kensington lock slot is used to attach a cable and lock to
the Cisco WAP125.
Default Settings
Parameter
Default Value
Username
cisco
Password
cisco
LAN IP Address
DHCP address assigned by server
Fallback LAN IP
192.168.1.245
Subnetwork Mask
255.255.255.0
If you are using a Cisco RV Series router, the default range for the DHCP assigned
address is from 192.168.1.100 to 192.168.1.254. Any device connecting to the same
LAN will be assigned an IP address in this range.
3 Mounting the Cisco WAP125
You can place the Cisco WAP125 horizontally on a surface so that it sits on its four
rubber feet, or place it vertically on a desktop by using the stand on its left side.
To place the Cisco WAP125 vertically on a desktop, follow these steps:
STEP 1 Locate the left side panel of the Cisco WAP125, and rotate the stand 90
degrees clockwise or anticlockwise.
STEP 2 Place the stand upward so that the Cisco WAP125 stands on a flat desktop.
Placement Tips
Ambient Temperature—To prevent the Cisco WAP125 from overheating, do
not operate it in an area that exceeds an ambient temperature of 104°F (40°C).
Air Flow—Be sure there is adequate air flow around the device.
Mechanical Loading—The Cisco WAP125 should be level, stable, and secure to
prevent it from sliding or shifting out of position.

Other manuals for Cisco WAP125

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco WAP125 and is the answer not in the manual?

Cisco WAP125 Specifications

General IconGeneral
2.4 GHzYes
MIMO typeMulti User MIMO
Modulation16-QAM, 64-QAM, 256-QAM, BPSK, CCK, QPSK
Number of users64 user(s)
Networking standardsIEEE 802.3af, IEEE 802.11ac
Spread spectrum methodDSSS, OFDM
Ethernet LAN data rates10, 100, 1000 Mbit/s
Maximum data transfer rate867 Mbit/s
Security algorithmsWPA, WPA2
Number of SSID supported8
Supported network protocolsIPv6, NTP, HTTP, HTTPS
USB 2.0 ports quantity0
Ethernet LAN (RJ-45) ports1
Output current1 A
Output voltage12 V
Power plug typeType C
AC input voltage100 - 240 V
AC input frequency50 Hz
PlacementDesk
CertificationUL 60950-1, CAN/CSA-C22.2 No. 60950-1, IEC 60950-1, EN 60950-1, FCC 15.247, 15.407; RSS-210; EN 300.328, EN 301.893; AS/NZS 4268.2003; FCC 15.107 15.109, ICES-003, EN 301.489-1 -17
Product colorWhite
Recommended usageIndoor
Cable lock slot typeKensington
Antenna typeInternal
Antenna gain level (max)5.63 dBi
Flash memory128 MB
Internal memory256 MB
Operating system installedLinux
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 40 °C
Storage relative humidity (H-H)5 - 90 %
Operating relative humidity (H-H)10 - 85 %
Country of originChina
Quantity per pack1 pc(s)
Package depth188.976 mm
Package width168.91 mm
Package height80.01 mm
Package weight1133.98 g
Weight and Dimensions IconWeight and Dimensions
Width123.19 mm
Height31.75 mm
Weight303.91 g

Related product manuals