Cisco WAP125 User Manual

8 Cisco WAP125 Quick Start Guide
Incorrect IP Address
The most likely cause of connectivity failure is an incorrect IP address. The Web
browser may be pointing to the wrong IP address, or your computer may be
configured with an IP address that is not in the same subnet as the Cisco WAP125.
Because the factory default IP address configuration is DHCP, make sure that your
DHCP server is running and can be reached. You may need to disconnect and
reconnect the devices for them to discover their new IP addresses from the DHCP
server. You can then query the DHCP server for the new IP address. See Step 2 of
Getting Started with the
Configuration for more information on how to find the DHCP address.
If the Cisco WAP125 does not receive a DHCP response (there is no DHCP server on
your network) after 60 seconds, the Cisco WAP125 will fallback to the following
default static IP address: 192.168.1.245 and a default mask of 255.255.255.0. To
reach that IP address, be sure that your computer is on the 192.168.1.xxx network.
8 Rebooting the Cisco WAP125 or Resetting to
Factory Defaults
To reboot your Cisco WAP125:
• If the Cisco WAP125 uses a power adapter, with the power on, use the POWER
button to reboot the device. The POWER button only functions when the Cisco
WAP125 uses a power adapter.
• If the power supply is PoE, unplug your Ethernet connection for three seconds
and plug it back in.
• With the power on, press the RESET button with an opened paper clip for less
than 10 seconds, or until the lights go off.
– When all the lights go off, release the RESET button.
– Release the RESET button as soon as the lights go off, or you will restore
the Cisco WAP125 to factory default settings and lose your configurations.
To reset the Cisco WAP125 to factory default settings:
• With the power on, press and hold the RESET button with an opened paper clip
for more than 10 seconds.
– All of the lights will go off.
– Release the RESET button when the power light turns on.

Cisco WAP125 Specifications

General

2.4 GHz	Yes
MIMO type	Multi User MIMO
Modulation	16-QAM, 64-QAM, 256-QAM, BPSK, CCK, QPSK
Number of users	64 user(s)
Networking standards	IEEE 802.3af, IEEE 802.11ac
Spread spectrum method	DSSS, OFDM
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	867 Mbit/s
Security algorithms	WPA, WPA2
Number of SSID supported	8
Supported network protocols	IPv6, NTP, HTTP, HTTPS
USB 2.0 ports quantity	0
Ethernet LAN (RJ-45) ports	1
Output current	1 A
Output voltage	12 V
Power plug type	Type C
AC input voltage	100 - 240 V
AC input frequency	50 Hz
Placement	Desk
Certification	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, IEC 60950-1, EN 60950-1, FCC 15.247, 15.407; RSS-210; EN 300.328, EN 301.893; AS/NZS 4268.2003; FCC 15.107 15.109, ICES-003, EN 301.489-1 -17
Product color	White
Recommended usage	Indoor
Cable lock slot type	Kensington
Antenna type	Internal
Antenna gain level (max)	5.63 dBi
Flash memory	128 MB
Internal memory	256 MB
Operating system installed	Linux
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %
Country of origin	China
Quantity per pack	1 pc(s)
Package depth	188.976 mm
Package width	168.91 mm
Package height	80.01 mm
Package weight	1133.98 g

Weight and Dimensions

Width	123.19 mm
Height	31.75 mm
Weight	303.91 g