1/2
Component identification
Date indication
Hour hand
Minute hand
Function hand
• Day of week
• Year (years since leap
year: L.Y./+1/+2/+3)
• Alarm setting (ON/OFF)
Mode hand
24-hour hand
Second hand
Button
B
Button
A
Crown
• Actual appearance may differ from the illustration.
• The crown has two positions when pulling it out.
• Refer also to our web page for detail of usage of the
scale and bezel on the watch.
(
http://www.citizenwatch-global.com/support/
pdf/enhanced/e.pdf
)
Changing the mode
This watch features the four different modes as follows:
TME
The normal time is indicated.
CAL
The calendar is indicated. The second hand points the month and the function
hand points day of week.
• The function hand points the years since leap year (L.Y./+1/+2/+3) while pressing the
upper right button
B
. Refer to
Setting the calendar
to see further information about the
years since leap year.
ALM
The alarm time is indicated.
L-TM
Local time is indicated.
• Date indication and day of week are those of [TME] even in this mode.
1.
Pull the crown out to position
1
.
The second hand points to 30 seconds and stops.
2.
Rotate the crown to change the mode.
• Turn the crown so that the mode hand will point to a marker of the mode
indication securely.
3.
Push the crown in to position
0
to finish the procedure.
Indication of the watch changes into that of the mode selected.
• It may take some time to change indication.
E870 Abbreviated instruction
• This watch is solar-powered. Expose the dial to light and use it sufficiently charged.
• To see details of charging time, specifications and operations, refer to the instruction manual:
E870 instruction manual
English
Setting the time
Adjust the time of the mode [TME].
• The time of [L-TM] is automatically adjusted following the setting of time
difference from the time of [TME].
1.
Change the mode to [TME] and pull the crown out to position
2
.
The second hand points to 0 second.
2.
Rotate the crown to set the time.
• The hour, minute and 24-hour hands move synchronously.
• Check whether the time set is AM or PM with the 24-hour hand.
• When you rotate the crown quickly, the hand will move continuously. To
stop the rapid movement, rotate the crown in either direction.
3.
Push the crown in to position
0
in accordance with a reliable
time source.
Setting the calendar
Adjust the calendar of the mode [TME].
1.
Change the mode to [CAL] and pull the crown out to position
2
.
The second hand points the month and the function hand points the years
since leap year.
2.
Press and release the upper right button
B
repeatedly to
change the hand/indication to be corrected.
• Each time you press button
B
, the target changes as follows:
• Year → month → date → day of week → (Back to the top)
3.
Rotate the crown to adjust the hand/indication.
• For year, set the years since leap year referring to the table below.
Year
Indication of the
function hand
Years since leap
year
2016 2020 2024 2028 L. Y. 0
(Leap year)
2017 2021 2025 2029 +1 1
2018 2022 2026 2030 +2 2
2019 2023 2027 2031 +3 3
• Date indication changes to the next as the function hand rotates 4 times.
4.
Repeat steps 2 and 3.
5.
Push the crown in to position
0
to finish the procedure.
Setting the local time
You can set time difference from the time of [TME] in 1-hour increments to
indicate the local time.
• The time difference is adjustable within a range of ±23 hours from the time of
[TME].
1.
Change the mode to [L-TM] and pull the crown out to position
2
.
Local time is indicated.
2.
Rotate the crown to adjust the hour hand.
• The hour hand moves in 1-hour increments and the 24-hour hand moves
synchronously with it.
• When you rotate the crown quickly, the hand will move continuously. To
stop the rapid movement, rotate the crown in either direction.
3.
Push the crown in to position
0
to finish the procedure.
Crown's position
0 1 2
To Next Page
Need help?
General
