CITIZEN Bluetooth Watch W770 Troubleshooting
The time and calendar of the watch is not corrected even after connection
To make the watch receive time info during connection with the smartphone, the function must be activated on the app.
Proceed operation following step numbers below. To check the operation movie, click the icon
Video
on the PDF.
1
Checking the smartphone
1
Check time and calendar of the smartphone.
2
Start the dedicated app.
3
Turn on “Time Sync” on the dedicated app.
2
Checking the power reserve
You cannot connect the watch and the smartphone when the power reserve
level of the watch is “0”.
S
M
T
W
T
F
S
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
60
30
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
60
30
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
Button
B
Button
A
Function
hand
Crown
Mode hand
Pull the crown out to position
1
and rotate it to move
the mode hand to choose a
mode.
It takes three
positions.
Second hand
Connection status
Power reserve
1
Change the mode to [
TME
] or [
L-TM
] and push the crown in
to position 0.
2
Press the lower right button A repeatedly to make the
function hand indicate power reserve.
3
Disconnecting
• Proceed to the next step if it is not connected.
1
Change the mode to [
TME
] and push the crown in to position
0.
2
Press and hold the upper right button B for 4 seconds.
The second hand points “
ACT
(40-second position)” and, after
disconnection, the function hand points “
OFF
” of connection
status.
4
Connecting
• The watch cannot be connected with a non-registered smartphone.
1
Change the mode to [
TME
] and push the crown in to position
0.
2
Press and release the upper right button B.
The second hand points “
ACT
(40-second position)” and, after
connection, the function hand points “
ON
” of connection status.
When the time and calendar of the watch are not corrected even after
connection, remove the registration information and register the
phone again.
5
Checking registration information
1
Start the dedicated app on a smartphone which has ever
been connected with the watch.
2
Check “Paring info” on the app to see saving destination of
the smartphone you want to register again.
6
Removing registration information
Remove registration information of the smartphone used for time info
reception and those not being used.
1
Change the mode to [
TME
] and pull the crown out to position
2.
The second hand points the registration information currently
chosen and the function hand indicates connection status (
ON/OFF
).
Registration information 1
Registration information 2
Registration information 3
60
30
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
2
Rotate the crown to choose registration information to
remove.
3
Press and hold the upper right button B for about 7 seconds.
The second hand turns fully around and removing is finished.
4
Rotate the crown to choose another registration information.
5
Repeat steps 3 and 4.
6
Push the crown in to position 0.
The second hand and function hand return to normal indication.
7
Remove “
Eco-Drive W770
” from the list of registered devices
in the Bluetooth setting on the smartphone.
• When “
Eco-Drive W770
” cannot be seen, it has already been deleted.
Video
Video
Video
Video
Continue to the next page
To Next Page
Loading...
