Citizen W770 - Time and Troubleshooting; Adjusting Time and Calendar Manually; Checking and Correcting Reference Position

8/11
CITIZEN Bluetooth Watch W770 Instruction manual
Adjusting the time and calendar manually
You can set the time and calendar of the [TME] mode manually.
• The local time is also corrected automatically when the time is set.
1
Change the mode to [TME] (page 2) and pull the crown out
to position
2
.
The second hand points the registration information currently
chosen.
2
Press and hold the lower right button
A
for 2 seconds or more.
The second hand stops at 0 second and the minute hand slightly
moves.
3
Press and release the lower right button
A
repeatedly until
the hand/indication to be corrected is selected.
• Each time you press button
A
, the target changes as follows.
Hour/minute
→
date
→
year/month
→
day of week
→
(back to the
top)
• The hand or indication slightly moves when selected to show it
becomes adjustable.
4
Rotate the crown to adjust the hand/indication.
• The hour, minute and 24-hour hands move in conjunction with
one another.
• Check AM/PM referring to the 24-hour hand.
• Year and month are indicated with the second hand.
• Date indication changes to the next as the function hand rotates 5
times.
• When you rotate the crown quickly a few times, the hands
and date indication will move continuously. To stop the rapid
movement, rotate the crown in either direction.
5
Repeat steps 3 and 4.
6
Push the crown in to position
0
in accordance with a reliable
time source to finish the procedure.
Month and year indications
Set the year and month with the position of the second hand.
24 60
30
12
6
18
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
12
1
2
3
4
5
6
7
8
9
10
11
“Month” corresponds to one of the 12
zones shown in the figure below.
Each number means month.
“Year” corresponds to the years since
leap year and is indicated with markers
in the zone of each month.
1
2
24
60
30
12
6
18
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
Years since leap year:
0
(Leap year)
0
Years since leap year:
1
Years since leap year:
2
Years since leap year:
3
3
Actual year
Years since leap
year
Second hand position
2016 2020 2024 2028 0
(Leap year) Hour marker
2017 2021 2025 2029 1
1st min. marker
2018 2022 2026 2030 2
2nd min. marker
2019 2023 2027 2031 3
3rd min. marker
Examples: Position of the second hand when setting August 2016
You can find that the years since leap year of 2016 is “0” from
the table and the second hand must be set to the hour marker of
August zone.
24 60
30
12
6
18
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
Troubleshooting
Checking and correcting the reference position
If the time or calender is not shown correctly even after proper reception of the
time info, check whether the reference position is correct.
• If the hands and indication do not reflect the correct reference position, the time
and calendar will not be indicated accurately even if the time info is received.
What is the reference position?
The base position of all hands and calendar to properly
indicate the various functions of this watch.
• Hour, minute and second hands: 0 hour 00 minute 0
second
• 24-hour hand: “24”
• Date indication: midway between “31” and “1”
• Function hand: “30” (straight down)
Correct reference positions
24 60
30
12
6
18
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
1
Change the mode to [CHR] (page 2) and pull the crown out
to position
2
.
The second hand moves to the current reference positions stored in
memory and stops.
2
Press and hold the lower right button
A
for 2 seconds.
The hands and indication start to move to the current reference
positions stored in memory.
• Release the button as the hands start to move.
3
Check the reference positions of them referring to the
illustration above.
Correct
Push the crown in to position
0
to finish the
procedure. Set the mode to [TME] after that.
Wrong
Proceed to step 4 and correct the reference position.
4
Press and release the lower right button
A
.
The function hand slightly moves and the hand and date indication
become adjustable.
5
Press and release the lower right button
A
repeatedly until
the hand/indication to be corrected is selected.
• Each time you press the button, the target changes as follows:
Function hand/date indication
→
Hour/minute/24-hour hands
→
Second
hand
→
(back to the top)
• The hand slightly moves when selected to show it becomes
adjustable.
• The function hand points “60” (straight up) when the hour,
minute and 24-hour hands are the targets of adjustment.
6
Rotate the crown to adjust the hand/indication.
• The hour, minute and 24-hour hands move in conjunction with
one another.
• Date indication changes to the next as the function hand rotates 5
times.
• When you rotate the crown quickly a few times, the hand/
indication will move continuously. To stop the rapid movement,
rotate the crown in either direction.
7
Repeat steps 5 and 6.
8
Push the crown in to position
0
.
9
Change the mode to [
TME
] to finish the procedure.