Claas MEDION 310 - Page 10

0.1.8 RHB MEDION 340 - 310 - 299 216.0
Contents
Disassembling the axle drive
(MEDION 330 – 310) ................................................... 7.20.26
Axle drive, exploded view
(MEDION 330 – 310) ................................................... 7.20.32
Assembling the axle drive
(MEDION 330 – 310) ................................................... 7.20.33
Rear axle .............................................................................. 7.21.1
Removing the wheel bearings
(2.05 m rear axle) .......................................................... 7.21.1
Wheel bearing, exploded view
(2.05 m rear axle) .......................................................... 7.21.3
Installing the wheel bearings
(2.05 m rear axle) .......................................................... 7.21.3
Removing the stub axles
(2.05 m rear axle) .......................................................... 7.21.5
Stub axle, exploded view
(2.05 m rear axle) .......................................................... 7.21.8
Installing the stub axles
(2.05 m rear axle) .......................................................... 7.21.8
Removing the wheel bearings
(2.40 m rear axle / adjustable rear axle) ...................... 7.21.10
Wheel bearing, exploded view
(2.40 m rear axle / adjustable rear axle) ...................... 7.21.12
Installing the wheel bearings
(2.40 m rear axle / adjustable rear axle) ...................... 7.21.13
Removing the stub axles
(2.40 m rear axle / adjustable rear axle) ...................... 7.21.15
Stub axle, exploded view
(2.40 m rear axle / adjustable rear axle –
MEDION 330 – 310) .................................................... 7.21.18
Stub axle, exploded view
(adjustable rear axle – MEDION 340) .......................... 7.21.18
Installing the stub axles
(2.40 m rear axle / adjustable rear axle) ...................... 7.21.18
Adjusting the rear axle stops
(2.05 m rear axle, 2.40 m rear axle,
adjustable rear axle) .................................................... 7.21.21
Adjusting the rear axle stops
(CLAAS 4-Trac axle) .................................................... 7.21.22
Adjusting the track width .............................................. 7.21.23
Removing the rear axle ................................................ 7.21.25
Installing the rear axle .................................................. 7.21.27
Removing the CLAAS 4-Trac axle ............................... 7.21.29
Installing the CLAAS 4-Trac axle ................................. 7.21.31
Removing the CLAAS 4-Trac system .......................... 7.21.34
CLAAS 4-Trac system, exploded view ........................ 7.21.37
Installing the CLAAS 4-Trac system ............................ 7.21.38
Removing the stub axle housings
(CLAAS 4-Trac system) ............................................... 7.21.40
Installing the stub axle housings
(CLAAS 4-Trac system) ............................................... 7.21.42
8. Machine body
9. Hydraulic system
Hydraulic tank ........................................................................ 9.1.1
Removing the hydraulic tank ........................................... 9.1.1
Hydraulic tank, exploded view ......................................... 9.1.3
Installing the hydraulic tank ............................................. 9.1.3
Checking the hydraulic oil level
(Hydrostatic ground drive
and working hydraulics) ................................................... 9.1.5
Hydraulic oil cooler ................................................................ 9.2.1
Removing the hydraulic oil cooler ................................... 9.2.1
Installing the hydraulic oil cooler ..................................... 9.2.2
Hydraulic pump ...................................................................... 9.3.1
Removing the double pump ............................................ 9.3.1
Disassembling the double pump ..................................... 9.3.2
Double pump, exploded view .......................................... 9.3.3
Assembling the double pump .......................................... 9.3.3
Installing the double pump .............................................. 9.3.4
Removing the hydraulic variable-displacement pump
(Linde HPV 105) .............................................................. 9.3.7
Hydrostatic ground drive, exploded view
(Linde HPV 105) ............................................................ 9.3.10
Installing the hydraulic variable-displacement pump
(Linde HPV 105) ............................................................ 9.3.11
Venting the hydrostatic system ..................................... 9.3.16
Bleeding the CLAAS 4-Trac system .............................. 9.3.17
Hydraulic motor ..................................................................... 9.4.1
Removing the ground drive hydraulic motor
(Linde HMV 105) ............................................................. 9.4.1
Installing the ground drive hydraulic motor
(Linde HMV 105) ............................................................. 9.4.3
Low-pressure hydraulic system control valves ...................... 9.5.1
Removing the low-pressure hydraulic system
solenoid valve .................................................................. 9.5.1
Low-pressure hydraulic system solenoid valve,
exploded view .................................................................. 9.5.4
Installing the low-pressure hydraulic system
solenoid valve .................................................................. 9.5.5
Removing the low-pressure hydraulic system
pressure relief valve ........................................................ 9.5.6
Installing the low-pressure hydraulic system
pressure relief valve ........................................................ 9.5.7
Adjusting / checking the low-pressure hydraulic
system pressure relief valve ............................................ 9.5.7
Removing the 3-D sieve pan
pendulum control ............................................................. 9.5.8
Disassembling the 3-D sieve pan
pendulum control ............................................................. 9.5.8
3-D sieve pan pendulum control,
exploded view ................................................................ 9.5.10
Assembling the 3-D sieve pan
pendulum control ........................................................... 9.5.11
Installing the 3-D sieve pan
pendulum control ........................................................... 9.5.12
Working hydraulics control valves ......................................... 9.6.1
Removing the grain tank unloading tube lock-up
valve unit ......................................................................... 9.6.1
Grain tank unloading tube lock-up valve unit,
exploded view .................................................................. 9.6.1
Installing the grain tank unloading tube lock-up
valve unit ......................................................................... 9.6.2
Removing the CLAAS Auto-Contour lock-up
valve unit ......................................................................... 9.6.3
CLAAS Auto-Contour lock-up valve unit,
exploded view .................................................................. 9.6.3
Find manuals at http://best-manuals.com/search?&s=CLA-2992160