299 216.0 - RHB MEDION 340 - 310 0.1.9
Contents
Installing the CLAAS Auto-Contour lock-up
valve unit ......................................................................... 9.6.4
Removing the working hydraulics pressure
relief valve ....................................................................... 9.6.5
Disassembling the working hydraulics pressure
relief valve ....................................................................... 9.6.5
Working hydraulics pressure relief valve,
exploded view .................................................................. 9.6.7
Assembling the working hydraulics pressure
relief valve ....................................................................... 9.6.8
Installing the working hydraulics pressure relief valve ..... 9.6.9
Adjusting / checking the working hydraulics pressure
relief valve ..................................................................... 9.6.10
Removing the front working hydraulics
valve block ..................................................................... 9.6.11
Installing the front working hydraulics
valve block ..................................................................... 9.6.12
Removing the 3/3-way drum speed adjustment valve ... 9.6.12
Disassembling the 3/3-way drum speed
adjustment valve ............................................................ 9.6.13
3/3-way drum speed adjustment valve,
exploded view ................................................................ 9.6.15
Assembling the 3/3-way drum speed
adjustment valve ............................................................ 9.6.16
Installing the 3/3-way drum speed adjustment valve ..... 9.6.17
Removing the 4/3-way hydraulic fore and aft reel
adjustment and CLAAS Auto-Contour solenoid valve ... 9.6.18
4/3-way hydraulic fore and aft reel adjustment and
CLAAS Auto-Contour solenoid valve, exploded view .... 9.6.19
Installing the 4/3-way hydraulic fore and aft reel adjustment
and CLAAS Auto-Contour solenoid valve ...................... 9.6.20
Removing the rear working hydraulics
valve block ..................................................................... 9.6.21
Installing the rear working hydraulics
valve block ..................................................................... 9.6.23
Removing the 3/3-way raise / lower reel and
raise / lower cutterbar solenoid valve ............................ 9.6.23
Disassembling the 3/3-way raise / lower reel and
raise / lower cutterbar solenoid valve ............................ 9.6.24
3/3-way raise / lower reel and raise / lower cutterbar
solenoid valve, exploded view ....................................... 9.6.29
Assembling the 3/3-way
raise/lower reel and
raise/lower cutterbar solenoid valve .............................. 9.6.30
Installing the 3/3-way
raise / lower reel and
raise / lower cutterbar solenoid valve ............................ 9.6.31
Removing the 4/3-way swing grain tank
unloading tube solenoid valve ....................................... 9.6.32
4/3-way swing grain tank unloading tube
solenoid valve, exploded view ....................................... 9.6.33
Installing the 4/3-way swing grain tank unloading tube
solenoid valve ................................................................ 9.6.34
Removing the CLAAS Auto-Contour flow
control valve .................................................................. 9.6.35
CLAAS Auto-Contour flow control valve,
exploded view ................................................................ 9.6.35
Installing the CLAAS Auto-Contour flow
control valve .................................................................. 9.6.36
Removing the CLAAS Autopilot
master valve .................................................................. 9.6.36
CLAAS Autopilot master valve,
exploded view ............................................................... 9.6.37
Installing the CLAAS Autopilot
master valve .................................................................. 9.6.37
Removing the CLAAS Autopilot solenoid
valve block .................................................................... 9.6.38
CLAAS Autopilot solenoid valve block,
exploded view ............................................................... 9.6.40
Installing the CLAAS Autopilot solenoid
valve block .................................................................... 9.6.41
Low-pressure hydraulic system
hydraulic cylinder ................................................................... 9.7.1
Removing the threshing mechanism circuit
hydraulic cylinder ............................................................ 9.7.1
Disassembling the threshing mechanism
circuit hydraulic cylinder .................................................. 9.7.2
Threshing mechanism circuit hydraulic cylinder,
exploded view ................................................................. 9.7.3
Assembling the threshing mechanism circuit
hydraulic cylinder ............................................................ 9.7.4
Installing the threshing mechanism circuit
hydraulic cylinder ............................................................ 9.7.5
Removing the grain tank circuit hydraulic cylinder
(MEDION 340) ................................................................ 9.7.6
Installing the grain tank circuit hydraulic cylinder
(MEDION 340) ................................................................ 9.7.7
Removing the grain tank circuit hydraulic cylinder
(MEDION 330 – 310) ...................................................... 9.7.8
Installing the grain tank circuit hydraulic cylinder
(MEDION 330 – 310) ...................................................... 9.7.9
Disassembling the grain tank circuit
hydraulic cylinder .......................................................... 9.7.10
Grain tank circuit hydraulic cylinder,
exploded view ............................................................... 9.7.11
Assembling the grain tank circuit
hydraulic cylinder .......................................................... 9.7.11
Removing the cutterbar clutch
rotary coupling ............................................................... 9.7.12
Disassembling the cutterbar clutch
rotary coupling ............................................................... 9.7.13
Assembling the cutterbar clutch
rotary coupling ............................................................... 9.7.15
Installing the cutterbar clutch
rotary coupling ............................................................... 9.7.17
Removing the cutterbar clutch
hydraulic cylinder .......................................................... 9.7.17
Disassembling the cutterbar clutch
hydraulic cylinder .......................................................... 9.7.18
Rotary coupling / Cutterbar clutch hydraulic cylinder,
exploded view ............................................................... 9.7.19
Assembling the cutterbar clutch
hydraulic cylinder .......................................................... 9.7.20
Installing the cutterbar clutch
hydraulic cylinder .......................................................... 9.7.22
Removing the 3-D cleaning system
hydraulic cylinder .......................................................... 9.7.22
To Next Page
Loading...
