Sirius Satellite Radio Operations
Switching the display
1. Press the [DISP] button to select the sub
display.
2.
In
the sub display, press and hold the [DISP]
button for 1 second
or
longer to cycle
between the following display modes:
Channel name
-+
title
-+
artist name
-+
category name
-+
text
-+
channel name
.....
Notes:
• The Operation status indication
of
the source unit
displays the abbreviated channel name for 2
seconds when
a station is selected before
returning to the previous display mode.
• Scrolling starts when the channel name
or
other
text has been displayed for
2 seconds. When
scrolling finishes, the first text display appears.
To
start scrolling again, press the [MENU] button.
Channel selection
Channels are selected with the following buttons.
• The
[<~]
or
[~>]
button
• The [DIRECT] buttons
• The [CAT] button
*For details, see the following operation
descriptions.
Note:
• The audio output
is.
muted
and
other button
operations are
not
accepted during channel
selection.
Tuning
There are 3 types
of
tuning mode available,
seek
tuning, manual tuning and preset tuning.
Seek tuning
Only channels that can be received are selected
while channels without broadcasts and channels
not covered by the contract are automatically
skipped.
1. Press the
[<~]
or
[~>]
button.
The receiver seeks the next available
channel below
or
above the current channel.
2. Press and hold the
[<~]
or
[~>]
button.
The receiver moves to seek channels below
or
above the current channel. If the channel
found when either button is released is
available that channel is received.
Otherwise, seeking continues until an
available channel is found.
18
CMD4
Manual tuning
Any channel including channels without
broadcasts and channels not covered
by
the
contract can be selected during manual tuning.
1. Press the [SEEK/MAN] button.
*This changes the seek mode to manual mode
and the "MANU" indicator on the display
lights. When this operation is performed in
manual mode, the seek mode is engaged and
the "MANU" indicator on the display goes off.
Notes:
• Operations cannot
be
performed for two seconds
afterpressing the [SEEK/MAN] button.
• The receiver automatically reverts
to
the seek
mode when the
[<~]
or
[~>]
button is
not
used for
7 seconds in the manual mode.
2. Press the
[<~]
or
[~>]
button. The receiver
moves to channels above
or
below the
current channel one by one.
3. Press and hold the
[<<llIIII]
or
[~>]
for 1 second
or longer.
The receiver moves to seek channels below
or above the current channel and the
channel found when either button is released
is received.
Recalling a preset channel
A total
of
18 SIRIUS channels can be stored (6-
SR1, 6-SR2 and 6-SR3). This allows you to
select your favorite SIRIUS channels and store
them in memory for later recall.
1.
Press the [SAT] button and select the desired
SIRIUS band (SR1, SR2 or SR3).
2.
To
recall a stored SIRIUS channel, press the
desired [DIRECT] button to select that
channel.
* Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store the current
channel into preset memory.
Manual memory
1.
Select the desired channel with seek tuning,
manual tuning
or
preset tuning.
2. Press and hold one of the [DIRECT] buttons
for 2 seconds
or
longer to store the current
channel into preset memory.
Notes:
• When the name
of
a channel stored in memory is
changed
by
a broadcasting channel, the display
may
show
a channel name that differs from the
stored name.
• A channel stored in memory
may
be discontinued
at
the option
of
the broadcasting channel.