Clarion CZ104E User Manual

English
7
CZ104E
Select tuner as playing source
Press [SRC / ] button once or more to
enter RADIO mode.
Selecting the radio band
Press the [AS/BAND] button to select one
radio band among FM1, FM2, FM3, MW
and LW .
Manual tuning
During manual tuning, the frequency will be
changed in steps.
Press the [
] or [ ] button to tune in
a higher / lower station.
Auto tuning
Press and hold the [ ] or [ ] button
to seek a higher / lower station.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When a station is received, searching stops
and the station is played.
Auto store
Only stations with sufcient signal strength
will be detected and stored in the memory.
Press and hold the [AS/BAND] button (1
sec.) to start automatic station search.
To stop auto store, press other buttons
having radio functions.
Notes:
1. After auto store, the previous stored
stations will be overwritten.
2. The unit has 5 bands, such as FM1, FM2,
FM3, MW and LW. FM3, MW and LW
can store by AS function. Each band can
store 6 stations, CZ104E can store 30
stations in total.
Manual store
When one expected radio station has been
detected, press and hold number button 1-6
to store it in the memory.
Radio Operations
Recall the stored stations
Press one numeric button among 1 to 6 on
the panel to select the corresponding stored
station.
Local seeking
When LOCAL seeking is ON, only those
radio stations with strong radio signal could
be received.
To select LOCAL function, press and hold
the [ DISP ] button, then press [
] button
repeatedly until LO or DX displays on the
screen, and rotate the [VOLUME] knob to
select Local or DX mode.
Note:
The number of radio stations that can be
received will decrease after the local seeking
mode is ON.
Radio Operations
Radio Data System
This unit has a built-in “Radio Data System”
decoder system that supports broadcast
stations transmitting “Radio Data System”
data.
When using the “Radio Data System”
function, always set the radio to FM mode.
AF function
The AF function switches to a different
frequency on the same network in order to
maintain optimum reception.
* The factory default setting is ON.
1. Set to system setup by long pressing
[DISP] button.
2. Press the [ ] or [ ] button to select
“AF”.
3. Rotate the [VOLUME] knob to select ON
or OFF.
• AF ON:
“ AF” indicator appears in the display and
AF function turns on.
• AF OFF:
“ AF” indicator disappears in the display
and AF function turns off.
Setting the TA standby mode
If you press and hold the [TA] button, “TA”
lights in the display and the unit is set into the
TA standby mode until a trafc announcement
is broadcast. When a traffic announcement
broadcast starts, “TRAF INF” appears in the
display. If you press and hold the [TA] button
while a trafc announcement broadcast is being
received, the traffic announcement broadcast
reception is cancelled and the unit goes into the
TA standby mode.
Cancelling the TA standby mode
As “TA” lights in the display, press and hold the
[TA] button. The “TA” in the display goes off
and the TA standby mode is cancelled.
PTY (Programme Type) Select
This function enables you to listen to a
broadcast of the selected programme type.
* Some countries do not yet have PTY
broadcast.
* In the TA standby mode, a TP station has
priority over a PTY broadcast station.
Selecting PTY
At Radio mode, press [MENU ] button, then
rotate the [VOLUME] knob to select PTY type,
press the [VOLUME] knob, the unit begin
searching.
REG (Regional programme)
function
When the REG function is ON, the optimum
regional station can be received. When this
function is OFF, if the regional station area
switches as you drive, a regional station for
that region is received.
* The factory default setting is ON.
Notes:
• This function is disabled when a national
station such as BBC R2 is being received.
• The REG function ON/OFF setting is valid
when the AF function is ON.
1. Set to system setup by long pressing [DISP]
button.
2. Press the [
] or [ ] button to select
“REG”.
3. Rotate the [VOLUME] knob to select ON or
OFF.
Manually tuning a regional station
in the same network
This function is valid when the AF function is
ON and the REG function is OFF.
Manually tuning a regional station
in the same network
This function is valid when the AF function is
ON and the REG function is OFF.
Note:
This function can be used when a regional
broadcast of the same network is received.
TA (Trafc Announcement)
In the TA standby mode, when a trafc
announcement broadcast starts, the trafc
announcement broadcast is received as top
priority regardless of the function mode so you
can listen to it. Trafc programme (TP)
automatic tuning is also available.
* This function can only be used when “TP”
appears in the display. When “TP” appears,
this means that the “Radio Data System”
broadcast station being received has traffic
announcement programmes.

Clarion CZ104E Specifications

General

Brand	Clarion
Model	CZ104E
Category	Car Receiver
Language	English