Why does my Clarion Car Receiver power not turn on?
The Clarion Car Receiver may not turn on due to a blown fuse. Replace it with a fuse of the same amperage. If it blows again, consult your store of purchase. Another cause could be incorrect wiring, in which case you should also consult your store of purchase.
What to do if my Clarion Car Receiver has no sound heard?
The absence of sound from your Clarion Car Receiver may be due to several reasons: * The speaker protection circuit might be operating. Try turning down the sound volume or turning the power off and on again. Note that speaker volume is reduced automatically when the speaker protection circuit operates. If the sound is muted again, consult our service department. * MP3/WMA files might be absent in a disc. Write MP3/WMA files onto the disc properly. * Files might not be recognized as an MP3/WMA file. Use MP3/WMA files encoded properly. * The file system might be incorrect. Use ISO9660 level 1, 2 or JOLIET or Romeo file system.
What to do if nothing happens when buttons are pressed on Clarion DB189RMP Car Receiver?
If nothing happens when you press the buttons on your Clarion Car Receiver, and the display is inaccurate, it could be due to a microprocessor malfunction caused by noise. Try turning off the power, then press Reset button the [RELEASE] button and remove the DCP. Press the reset button for about 2 seconds with a thin rod. Alternatively, the DCP or main unit connectors might be dirty. Wipe them off with a soft cloth moistened with cleaning alcohol.
How to fix sound skips or noisy sound on Clarion Car Receiver?
If the sound skips or is noisy on your Clarion Car Receiver, it could be because the compact disc is dirty. Clean it with a soft cloth. Alternatively, the compact disc may be heavily scratched or warped, in which case you should replace it with a compact disc with no scratches.
What to do if Clarion Car Receiver has no sound output with amplifiers or power antenna?
If there's no sound output when operating your Clarion Car Receiver with amplifiers or a power antenna attached, it could be because the power antenna lead is shorted to ground, or excessive current is required for remote-on the amplifiers or power antenna. To resolve this: 1. Turn the unit off. 2. Remove all wires attached to the power antenna lead and check each wire for a possible short to ground using an ohm meter. 3. Turn the unit back on. 4. Reconnect each amplifier remote wire to the power antenna lead one by one. If the amplifiers turn off before all wires are attached, use an external relay to provide remote-on voltage (excessive current required).
Why is the sound bad directly after power on Clarion Car Receiver?
If the sound is bad directly after powering on your Clarion Car Receiver, water droplets may have formed on the internal lens when the car was parked in a humid place. Let it dry for about 1 hour with the power on.
Why is sound cut or skipped on my Clarion DB189RMP Car Receiver?
If the sound is cut or skipped, or if noise is generated or mixed with the sound on your Clarion Car Receiver, the MP3/WMA files may not be encoded properly. Use MP3/WMA files encoded properly.
Why won't my Clarion DB189RMP turn on?
If your Clarion Car Receiver isn't turning on, there are a couple of potential reasons. First, the fuse might be blown; if this is the case, replace it with a fuse of the same amperage. Second, the wiring might be incorrect. Double-check the "Installation/Wire connection Guide" to ensure everything is wired properly.
What to do if there is no sound from my Clarion DB189RMP?
If you're not hearing any sound from your Clarion Car Receiver, it's possible the speaker protection circuit is activated. Try turning down the sound volume. You can also restore function by turning the power off and on again. Note that the speaker volume reduces automatically when this circuit operates.
What to do if buttons on my Clarion DB189RMP don't work?
If the buttons on your Clarion Car Receiver aren't working or the display is inaccurate, it could be due to a microprocessor malfunction caused by noise or other factors, or due to dirty connectors. First, turn off the power, then press the Reset button [RELEASE] button and remove the DCP. Press the reset button for about 2 seconds with a thin rod. If that doesn't work, try wiping the DCP or main unit connectors with a soft cloth moistened with cleaning alcohol.
Guidance on proper handling, storage, and cleaning of compact discs for optimal performance.
Detailed explanation of each button and its function on the car stereo unit.
Explanation of various indicators and symbols displayed on the unit's screen.
Information on how the display screen behaves in extreme cold conditions.
Instructions on how to safely detach and reattach the control panel, including storage advice.
Covers fundamental operations like turning the unit on/off, adjusting volume, and switching modes.
Guide to adjusting sound settings like EQ, bass, treble, and balance for personalized audio.
Details on configuring the Z-Enhancer Plus feature with various sound tone effects.
Instructions for adjusting the treble frequency and gain.
Guidance on adjusting the audio balance between left and right speakers.
Instructions on adjusting the audio balance between front and rear speakers.
Explanation of how to activate and control the MAGNA BASS EXTEND for enhanced bass.
Details on how the unit receives and displays clock time data from RDS stations.
Steps to select radio mode, band, and tune into desired stations.
Introduction to RDS features like station name display, AF switching, and traffic announcements.
Instructions for playing CDs, MP3, and WMA files, including format precautions.
How to change general settings like screen saver, title scroll, and dimmer control.
Troubleshooting steps for when the unit does not power on, including fuse and wiring checks.
Steps to resolve no sound output when amplifiers or power antenna are attached.
Procedure for unresponsive buttons, involving power cycling and using the reset button.
Troubleshooting for inaccurate display, involving connector cleaning and reset button use.
Steps to resolve no sound, including speaker protection circuit and file checks.
Troubleshooting for sound skipping or noise, involving disc condition and file encoding.
Steps to resolve sound cutting or skipping, particularly with MP3/WMA files.
Guidance for bad sound immediately after power-on, related to internal lens condensation.
Troubleshooting for wrong filenames, relating to file system correctness.
Troubleshooting for ERROR 2, indicating a CD is caught and cannot be ejected.
Troubleshooting for ERROR 3, where a CD cannot be played due to scratches or warping.
Troubleshooting for ERROR 6, where a CD is loaded incorrectly.
Technical specifications for the radio tuner, including tuning system and receiving frequencies.
Technical specifications for the CD player, covering system, frequency response, and audio quality.
General specifications including output power, voltage, consumption, impedance, weight, and dimensions.
General| Type | Car Receiver |
|---|---|
| Model | DB189RMP |
| Brand | Clarion |
| Power Output | 50W x 4 |
| RMS Power | 22W x 4 |
| Peak Output | 50W x 4 |
| Bluetooth | Yes |
| USB Port | 1 |
| Radio Tuner | AM/FM |
| Display | LCD |
| DIN Size | Single DIN |
| Detachable Face | Yes |
| HD Radio | No |
| SIRIUS or XM | No |
| AUX Input | Yes |
| USB Input | Yes |
| Memory Card Slot | No |
| Inputs | AUX, USB |
| Display Type | LCD |
| Equalizer | Yes |
| Supported Media | MP3/WMA |
To Next Page
