051-6069-08 FAN8047G3 4 channel Motor Driver
Function Table
SW45 Mute1,2_ Mute 3_ Mute 4_ 1 ch 2 ch 3 ch 4 ch
in in in i n out out out out
(pin 28) (pin 9) (pin 27) (pin 20) (pin13,14) (pin11,12) (pin17,18) (pin15,16)
H H H x ON ON ON ON A
H H L x ON ON OFF ON A
H L H x OFF OFF ON OFF
H L L x OFF OFF OFF OFF
L x x H OFF OFF OFF ON B
L x x L OFF OFF OFF OFF
051-6399-00 TC94A15F
CD IC
1.Terminal Description
pin 1: IPF OUT : O : IP flag output.
pin 2: S B O K O : O : Sub code Q data CRCC OK signal output.
pin 3: CLOCKIO :I/O: Th e clock pulse input/output for the sub
code reading.
pin 4: VDD : - : Positive supply voltage.
pin 5: V SS : - : Negative supply voltage.
pin 6: DATA : O : DATA
pin 7: SF S Y O : O : Playback frame synchronous signal output.
pin 8: SB SY O : O : Sub code block synchronous signal output.
pin 9: HSO : O : The play speed flag output.
pin 10: UHSO : O : The play speed flag output.
pin 11 : AR SEL IN : IN : Fix to the high level.
pin 12: AWRC : O : Th e control signal output for the active
wide range VCO.
pin 13: P VD D : - : PLL positive supply voltage.
pin 14: PDO : O : Phase difference signal output of EFM-
PLCK.
pin 15: TMAX S : O : T max judgment output.
pin 16: TMAX : O : T max judgment output.
pin 17: LPF N : IN : Inverted input of LPF for PLL.
pin 18 : LPF OUT : O : The output terminal for the Low Pass Fil-
ter.
pin 19 : P Vref : - : PLL reference voltage.
pin 20: VCO FILTER : O : Loop filter for VCO.
pin 21: VCO Ref : IN : VCO reference voltage input.
pin 22: D TC N : O : For the analog slicer.
pin 23: D T C P : O : For the analog slicer.
pin 24: P L L VSS : - : PLL ground.
pin 25: SLCO : O : Output of internal DAC for data slice level
generation.
pin 26: RF IN : IN : RF signal input.
pin 27 : R F R P : IN : RF ripple input.
pin 28: RF EQ OU T : O : The output of the RF equalizer.
pin 29: A VDD : - : Positive supply voltage for the Analog sec-
tion.
pin 30: R ES IN : - : For reference current setting.
pin 31: Vref OUT : O : The reference voltage output.
pin 32: VMDIR : O : T he reference voltage output.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Level
Shift
Level
Shift
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Level
Shift
Level
Shift
Vref 1
1ch in
2ch in
Reg on(H)
Reg feed
Reg out
Ground
P Vcc 1
Mute 1,2_
Ground
2chout-
2chout+
1chout-
1chout+
SW 45
Mute 3_
4chinB
Vref 2
4chinA
3chin
SVcc
PVcc
Mute 4_
Ground
3chout-
3chout+
4chout-
4chout+
Regulator
pin 34: INVSEL : IN : MDI polarity selection.
pin 35: AGCI : IN : The input terminal of RF AGC amplifier.
pin 36: RF DCI : IN : The input terminal for RF peak detection.
pin 37 : RF OUT : O : RF signal output.
pin 38: PN SEL : IN : The transistor type selection input for laser
diode driver. L=NPN, H=PNP.
pin 39: E Q SET : O : The equalizer setting terminal.
pin 40: R F VDD : - : RF power supply.
pin 41 : LDO : O : The laser diode drive output.
pin 42: MDI : IN : Monitor photo diode signal input.
pin 43: R F VS S : - : RF ground.
pin 44 : FNI 2 : IN : Main beam signal input.
pin 45 : FNI 1 : IN : Main beam signal input.
pin 46 : FPI 2 :IN : Main beam signal input.
pin 47 : FPI 1 :IN : Main beam signal input.
pin 48 : TPI : IN : Sub beam signal input.
pin 49 : TNI : IN : Sub beam signal input.
pin 50: FTEO : O : For test.
pin 51: RF ZI : IN : RF ripple zero cross signal input.
pin 52: A VSS : - : Analog ground.
pin 53 : R F R P : O : RF ripple signal output.
pin 54: RF DC : O : RF peak detection signal output. (hologram
suitable)
pin 55: FEI : O : Focus error signal output.
pin 56 : SBAD : O : Sub beam add signal output.
pin 57: TEI : O : Tracking error signal output.
pin 58 : TE Z I N : IN : Tracking error signal inpur for zero cross.
pin 59: A VDD : - : Positive supply voltage for the Analog sec-
tion.
pin 60: FOO : O : Focus equalizer output.
pin 61: TRO : O : Tracking equalizer output.
pin 62: Vref : O : Reference voltage output.
pin 63: FMO : O : Field equalizer output / Speed error output.
pin 64: DMO : O : Disk equalizer output.
pin 65: IO2A :I/O: General input/output.
pin 66: IO3A :I/O: General input/output.
pin 67: MONIT : O : Internal DSP signal monitor.
pin 68: FG IN : IN : FG input for the spindle CAV servo.
pin 69: V SS : - : Negative supply voltage.
pin 70: VDD : - : Positive supply voltage.
pin 71: TESIN : IN : For test.
pin 72: X VSS : - : Master clock analog ground.
pin 73: X I N : IN : Crystal connection.
pin 74: X O : O : Crystal connection.
pin 75: X V D D : - : Clock power supply.
pin 76: D V SS : - : Digital ground.
pin 77: RO : O : Right channel data output for 1-bit DAC.
pin 78 : D VDD : - : Positive supply voltage for the digital sec-
tion.
pin 79: D Vref : O : Digital reference voltage.
pin 80: LO : O : Left channel data output for 1-bit DAC.
pin 81: D V SS : - : Digital ground.
pin 82: Z DE T O : O : 1bit DAC zero flag output.
pin 83: V SS : - : Negative supply voltage.
pin 84: BUS 0 :I/O: CD IC Data input / output.
pin 85: BUS 1 :I/O: CD IC Data input / output.
pin 86: BUS 2 :I/O: CD IC Data input / output.
pin 87: BUS 3 :I/O: CD IC Data input / output.
pin 88: BU C K I N : IN : CD IC Data clock input.
pin 89: CCEI : IN : Chip enable input.
pin 90: RSTI : IN : Reset signal input.
pin 91: VDD : - : Positive supply voltage.
pin 92: EMPHI/FAO :I/O: Emphasis input for 1-bit DAC / Flag A
output.
pin 93: BCKI/FBO :I/O: Bi t c l ock input for 1-bit DAC / Flag B out-
put.
pin 94: AIN/FCO :I/O: Aud io inp u t f o r 1-bit DAC / Flag C output.
pin 95: LRCKI/FDO :I/O: LR clock input for 1-bit DAC / Flag D out-
put.
pin 96 : EMPHO : O : Emphasis flag output. H=Emphasis ON.
pin 97 : B C K O : O : Bit clock output.
pin 98: A OU T : O : Audio signal output.
pin 99 : L R CK O : O : LR clock output.
pin100 : D OUT : O : Serial data output.
CD section: 929-0301-83mechanism
pin 33 : T E S TR : O : The compensation terminal for RFEQO off-
set.
DXZ558RMP
-6-
To Next Page
Loading...
