Clarke MA50 15B CLARKE380B

Questions and Answers

C
Crystal PetersonAug 12, 2025
What to do if the Clarke MA50 15B CLARKE380B Floor Machine has insufficient vacuuming or water pickup?
- M
  Michelle SalinasAug 12, 2025
  If your Clarke Floor Machine isn't vacuuming or picking up water effectively, several factors could be at play. First, check if the recovery tank is full and empty it if necessary. Ensure the hose is properly connected to the squeegee. Inspect the vacuum assembly for any clogs and clean them out. Also, examine the squeegee for dirt or damage to the blades, cleaning or replacing them as needed. Finally, verify that the recovery tank is securely latched and the tank cover is properly closed with an intact gasket. Latch the lock (17) or close the cover properly or replace the gasket.
J
Jesus JordanAug 16, 2025
Why is the solution flow insufficient in my Clarke Floor Machine?
- C
  clarkjoseAug 16, 2025
  If the solution flow in your Clarke Floor Machine is insufficient, there are several possible causes. The solution filter might be dirty, so try cleaning it. The solution tank could be empty, so refill it. The solution flow control valve (31) might be clogged, requiring cleaning. Also, the solution itself might be dirty, so clean it.
C
Christopher LaraAug 20, 2025
What to do if my Clarke MA50 15B CLARKE380B does not work and the indicator light (51) is red?
- T
  Terri NicholsonAug 20, 2025
  If your Clarke Floor Machine isn't working and the indicator light (51) displays red, the batteries are likely discharged. Charge the batteries to resolve this issue.
N
Nathaniel GreenAug 25, 2025
How to fix a Clarke Floor Machine that does not work and the indicator lights (51) do not turn on?
- H
  Heather JohnsonAug 25, 2025
  If your Clarke Floor Machine isn't working and the indicator lights (51) aren't on, it could be due to a few reasons. First, check if the battery connector is disconnected and connect it. Second, the batteries might be completely discharged, so charge them. Third, the power line might be disconnected from the power source, so connect it.
A
Angela WilsonAug 27, 2025
Why does the squeegee on my Clarke Floor Machine leave marks on the floor?
- J
  Jade HillAug 27, 2025
  If the squeegee on your Clarke Floor Machine is leaving marks on the floor, it could be due to: * Debris under the squeegee blades. Remove the debris. * Worn, chipped, or torn squeegee blades. Replace the blades.
W
William MooreAug 31, 2025
What to do if the brush motor does not work and the brush indicator light (52) flashes on my Clarke MA50 15B CLARKE380B Floor Machine?
- N
  Nicole RamosAug 31, 2025
  If the brush motor isn't working and the brush indicator light (52) is flashing on your Clarke Floor Machine, it could be due to the deck motor being overloaded. Try using less aggressive brushes suitable for the floor you're cleaning. Alternatively, there might be an obstruction preventing the brush from rotating, so clean the brush hub.
J
James OlsonSep 3, 2025
What to do if the brush motor does not work and brush indicator light (52) does not turn on Clarke Floor Machine?
- M
  Mitchell RyanSep 4, 2025
  If the brush motor isn't working and the brush indicator light (52) isn't turning on, the PCB or key board might be broken. Change the PCB or key board.
J
Joe CaseySep 7, 2025
What to do if the vacuum system motor does not work and vacuum motor indicator light (53) does not turn on Clarke Floor Machine?
- M
  Mrs. Kelly YoungSep 7, 2025
  If the vacuum system motor isn't working and the vacuum motor indicator light (53) isn't turning on, the PCB or key board might be broken. Change the PCB or key board.