Clarke SE18C200 Operating & Maintenance Instructions

16 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

AIR COMPRESSOR

ELECTRIC MOTOR DRIVEN

OPERATING & MAINTENANCE

INSTRUCTIONS

1209

©

Table of Contents

Other manuals for Clarke SE18C200

Operation & Maintenance Instructions16 pages

Questions and Answers:

D
Daniel BairdAug 20, 2025
Why Clarke SE18C200 Air Compressor will not start automatically?
- P
  pmarshallAug 20, 2025
  There are several reasons why your Clarke Air Compressor might not start automatically: * A blown fuse: Check the fuse rating and replace it if necessary. * A tripped starter overload: Reset it by depressing the button. * A defective pressure switch: Have an electrician change the pressure switch. * Fault in electrical installation: Let an electrician check electrical installation.
D
David HarrisAug 22, 2025
Why does my Clarke SE18C200 run continuously and can’t attain the working pressure required?
- P
  Penny Webb MDAug 22, 2025
  If your Clarke Air Compressor runs continuously without reaching the required working pressure, consider the following: * Blocked suction filter: Change the filter. * Slack V-belt: Tighten the V-belt. * Leak between compressor block and air receiver: Tighten the connection and repair the leak. * Suction rendered difficult or impossible at suction intake or the air being taken in is too warm: Ensure unobstructed airflow around the unit.
B
brettspencerAug 25, 2025
What to do if Clarke Air Compressor unit starts and stops more frequently than usual?
- C
  Chelsey MillerAug 25, 2025
  If your Clarke Air Compressor starts and stops more frequently than usual, it could be due to: * Large amount of condensation in the air receiver: Drain off condensation at least once a week. * Leaks in the control unit or inspection cover: Locate leaks and repair them.
J
Jacob OwenAug 26, 2025
Why does my Clarke SE18C200 Air Compressor unit start, but stop again after only a few revolutions?
- J
  Jennifer PerezAug 26, 2025
  If your Clarke Air Compressor unit starts but stops after only a few revolutions, consider these causes: * Leaking non-return valve: Disconnect from the mains supply and empty air receiver. Clean or replace the non-return valve. * Blocked non-return valve: Thaw the non-return valve out. Ensure the unit is installed in a frost-free place.
S
Sue BrownAug 28, 2025
What to do if Clarke SE18C200 becomes too hot?
- C
  coreydavenportAug 28, 2025
  If your Clarke air compressor becomes too hot, it could be due to: * Insufficient ventilation: Ensure sufficient air is supplied to the flywheel or fan and that hot air is properly vented. * Low oil level: Fill with oil. * Dirt on cooling fins or the suction filter: Clean the cooling fins and suction filter.
T
Tim FoxAug 29, 2025
Why Clarke Air Compressor’s oil consumption rising?
- K
  Kimberly GeorgeAug 30, 2025
  If your Clarke Air Compressor's oil consumption is rising, consider these potential causes: * Too much oil in the compressor: Check the oil level a few minutes after stopping. * Working temperature of compressor too high because of insufficient cooling: Increase ventilation to air compressor. * Intake air filter blocked: Clean or change the air filter. * Unit too small in proportion to air consumption: Connect supplementary. * Semi-automatic unit Load too small: Convert to fully automatic operation.
J
Jamie GibsonAug 31, 2025
Why is there oil in the air delivered by my Clarke Air Compressor?
- D
  dmannAug 31, 2025
  If there is oil in the air delivered by your Clarke Air Compressor, it could be due to: * Sump over full: Reduce oil to the correct level. * Intake air filter blocked: Change the air filter.
M
Monica GoldenSep 2, 2025
What to do if Clarke SE18C200 Air Compressor unit starts when no air is being used?
- M
  mary66Sep 2, 2025
  If your Clarke Air Compressor unit starts when no air is being used, it is likely due to leaks in the pipework system. Locate and repair any leaks.
J
Jeremy BlackSep 4, 2025
How to fix unusual noise from Clarke SE18C200 Air Compressor?
- M
  mcunninghamSep 4, 2025
  If you notice an unusual noise from your Clarke Air Compressor, check the following: * Loose bolts: Tighten the bolts. * V-Belt flywheel or cooling coil touching belt guard: Find the place of contact and remedy the fault. * Loose flywheel: Tighten the flywheel. * Unit installed on an unsuitable base: Move the unit to a more solid base.
R
Roy OliverSep 6, 2025
What to do if Clarke SE18C200 keep blowing fuses?
- B
  Bonnie ConnerSep 6, 2025
  If your Clarke Air Compressor keeps blowing fuses, it might be due to an inadequate size fuse installed. Replace it with the correct fuse, referring to the chart.

Clarke SE18C200 Specifications

General

Brand	Clarke
Model	SE18C200
Category	Air Compressor
Language	English

Related product manuals

Preview: Clarke SE15

Clarke SE11C100

Clarke SE16C150

Clarke SE19C200

Preview: Clarke SE Series

Clarke SE Series

Clarke SEV11C100

Preview: Clarke SHHHAIR 30/9

Clarke SHHHAIR 30/9

Preview: Clarke JUMBO

Preview: Clarke HUNTER

Preview: Clarke XE Series

Clarke XE Series

Preview: Clarke Ranger 7/240

Clarke Ranger 7/240