CLIVET WSAT-2.230 - User Manual

 C. Art. M01B40M6 *E*%
$,5&22/('
:$7(5&+,//(5
:6$7 

 

 
 5&
,167$//$7,21
23(5$7,21$1'
0$,17(1$1&(0$18$/
*(1(5$/
THIS MANUAL CONTAINS THE FOLLOWING SECTIONS WHICH ARE TO BE CONSIDERED AN INTEGRAL PART
OF THE WHOLE AND ARE THEREFORE NOT TO BE DETACHED
G1B5GB-3 R1B5GB-3 E1B5GB-3 F1B5GB-3 C1B5GB-3
General Reception/Positioning Electrical connections Start-up Control
T1B5GB-3 M1B5GB-3 L1B5GB-3 K1B5GB-3
Troubleshooting Maintenance Water connections Residual Risks
,03257$17
The contents of this manual are designed to assure the
correct installation, adjustment and maintenance of the unit;
therefore:
− read the instructions with due care and attention;
− the appliance must be installed, tested and serviced by
properly qualified personnel (law n.45, 5.3.1990) licensed in
accordance with established legislation.
• The manufacturer declines all liability, and guarantee
coverage is automatically waived, if electrical and/or
mechanical modifications are made to the unit. Tampering
and unauthorized repairs or modifications to the unit will
automatically void the guarantee.
• Observe the safety regulations in force at the time of
installation.
• Make sure that the characteristics of the mains network
conform to the data on the serial number plate inside the
electrical panel.
• Conserve this manual and the circuit diagram with care.
Make sure that they are available for consultation by the
operator whenever necessary.
• Packing materials (plastic wrappings, expanded
polystyrene, nails, etc.) are potentially hazardous and must
be kept out of reach of children. Recycle packing materials
in accordance with local bylaws.
• The water chilled must be used only for the purpose for
which it is designed. The manufacturer bears no
responsibility in the case of applications other than the
specified use.
• Disconnect the unit in the case of breakdowns or
malfunctions.
• If repairs are necessary use only Clivet-approved service
centres and always insist on original spare parts.
The use of non-original parts and/or unauthorized service
centres may result in unsafe operation of the unit.
The manufacturer declines all liability for direct or indirect damage to property or injury
to persons resulting from failure to adhere to the instructions in this manual.
$'',7,21$/6$)(7<35(&$87216
This unit has been especially designed and manufactured so to prevent any risk to persons and health hazard.
For this reason, design solutions fit to eliminate (where possible) any cause of risk and sensibly reduce the probability of
danger have been adopted.
Please refer to the RESIDUAL RISKS section of this manual and strictly observe the behaviour prescriptions listed there in
order to prevent any possible risk that hasn’t been possible to avoid in the design stage.
Библиотека СОК 

Summary

General Sections

Reception and Positioning

Guidelines for the correct placement and installation of the unit.

Electrical Connections

Instructions for making safe and proper electrical connections to the unit.

Start-up

Procedures for initiating the unit's operation after installation.

Control

Information regarding the unit's control system and settings.

Troubleshooting

Guidance for diagnosing and resolving common operational issues.

Maintenance

Procedures for routine servicing and upkeep of the unit.

Water Connections

Instructions for connecting the unit's water circuits.

Residual Risks

Identification and management of any remaining risks after design safety measures.

Important Operational Guidelines

Additional Safety Precautions

Unit Configurations

Version Overview

Overview of different unit versions and their features, e.g., Standard, Energy Recovery.

Low Temperature Versions

Details on versions designed for operation at lower temperatures, including brine chiller.

Acoustic Configurations

Information on different acoustic configurations like ST, SC, LN, and EN.

Energy Efficiency Aspects

Notes on energy efficiency aspects, particularly for temperate climatic conditions.

Heat Exchanger Approvals

Details on approvals for heat exchangers, such as PED (CE) and internal testing (C).

Available Accessories

Exchanger Pressure Limits

Cut-out Devices and Controls Settings

Performance Correction Factors

Sound Level Data

Dimensional Data

CLIVET WSAT-2.230 Specifications

General

Brand	CLIVET
Model	WSAT-2.230
Category	Chiller
Language	English