Clover B14A - User Manual

Questions and Answers

A
Anthony HowellAug 18, 2025
What to do if the Clover Water Dispenser compressor does not run?
- H
  hmillerAug 18, 2025
  First, ensure the electric power outlet is turned on. If the issue persists, the thermostat may be misadjusted or defective, or the wiring may be faulty; adjust or replace the thermostat and check the wiring. Also, check if the line voltage is at least 90% of the minimum voltage and replace the overload protector if defective. Finally, the starting relay or the compressor itself could be defective, requiring replacement.
N
Natalie LeachAug 20, 2025
Why is my Clover Water Dispenser running constantly but the water is adequately chilled?
- K
  Kayla DoughertyAug 20, 2025
  The continuous running of your Clover Water Dispenser, despite adequately chilled water, may be due to poor ventilation or a dirty condenser. Ensure a minimum side and rear clearance of 4 inches and clean the condenser, or relocate the unit. Alternatively, the thermostat might be defective and need replacement or adjustment.
J
Julie PenaAug 22, 2025
Why is my Clover B14A compressor running continuously, but I don't have cold water?
- F
  fellisAug 23, 2025
  The continuous running of the Clover Water Dispenser compressor without producing cold water could indicate a substantial loss of refrigerant or a defective compressor. If a refrigerant leak is suspected, return the cooler to an authorized service center or the factory for repair.
V
Vanessa WhiteheadAug 26, 2025
How to fix a Clover B14A Water Dispenser that is making excessive noise?
- J
  jessica37Aug 26, 2025
  Excessive noise from your Clover Water Dispenser may be due to the cooler not being level; ensure it is placed on an even surface. Also, check the tubing inside the cooler to ensure it is not touching other parts and that all fixed screws are completely connected. If the noise persists, it may be due to the compressor's inherent operation, in which case it is a normal operating sound.
M
Michael Roberts IIIAug 27, 2025
What to do if hot water is not hot enough in my Clover B14A Water Dispenser?
- M
  Michael SheltonAug 28, 2025
  If the hot water from your Clover Water Dispenser is not hot enough, it could be due to usage exceeding the system's capacity. Be aware of the hot water system's maximum capacity. It may also indicate a defective hot control, which would need to be replaced.
K
Kimberly RitterAug 30, 2025
Why is the hot water in my Clover Water Dispenser not hot?
- E
  evansamandaAug 30, 2025
  If the hot water from your Clover Water Dispenser is not hot, first check if the hot water switch is turned on. If it is on, inspect for any loose or broken wire connections in the hot water system and repair as necessary, or replace the hot control. Also, check if the heat limiter is on and push the reset button, or replace the hot tank heater or assembly if defective.
M
Margaret AllisonSep 1, 2025
What to do if my Clover B14A hot tank is noisy?
- M
  Michelle SampsonSep 1, 2025
  If your Clover Water Dispenser's hot tank is noisy, it could be due to the hot tank heater being caked with mineral deposits. A slight boiling sound is normal during the heating cycle. Try de-liming the tank.
A
Anthony ReedSep 4, 2025
How to fix slow water flow from all faucets on a Clover Water Dispenser?
- J
  Justin CummingsSep 4, 2025
  If the water flow from all faucets of your Clover Water Dispenser is slow, and you have a Non Spill System, wait until the cold water tank refills after a large draw. Additionally, check the air filter and allow it to dry, as airflow will gradually return to normal as it dries.
J
Jordan CruzSep 6, 2025
Why does water drip from the Clover B14A Water Dispenser faucet?
- J
  jamiejonesSep 6, 2025
  If water drips from the faucet of your Clover Water Dispenser, try pressing down the faucet lever several times. If dripping persists, the faucet body packing and spring may be defective, requiring replacement of the faucet assembly.
B
Benjamin StewartSep 9, 2025
What causes slow hot water flow in a Clover Water Dispenser?
- M
  Michael StoutSep 9, 2025
  Slow hot water flow in your Clover Water Dispenser is by design to prevent splashing; this is a safety feature. If it's slower than usual, the faucet may be defective and need replacement. Another cause could be the hot tank being plugged with mineral deposits, requiring de-liming.

Summary

Safety Precautions

Specification and Parts Identification

Operation and Function of Parts

Cooling Operation

Explains the process of refrigerants compressing, condensing, and evaporating to cool water.

Heating Operation

Details how the electric heater inside the hot water tank heats supplied water for hot output.

Function of Parts

Lists and describes the function of each numbered component in the water cooler system.

Location Requirements

Installation Procedures

Storage

Cleaning

Troubleshooting Guide

Refrigeration System Troubleshooting

Addresses issues with the compressor not running, or water being inadequately chilled but cooler running continuously.

Hot Water System Troubleshooting

Covers problems like hot water not being hot, flowing slowly, or the hot tank being noisy.

Noise Troubleshooting

Details how to resolve excessive noise coming from the cooler, or noises related to the compressor.

Water Leakage Troubleshooting

Provides solutions for water drips from the faucet or leaks from inside or outside the appliance.

Non-Spill System Issues

Addresses slow water flow from all faucets and excessive water accumulation in the housing for this system.

Wiring Diagram

Exploded View for Model B14 A

Service Parts List for Model B14 A

Exploded View for Model B14 B

Service Parts List for Model B14 B

Clover B14A Specifications

General

Water Source	Bottled Water
Capacity	5 Gallons
Material	Plastic
Color	White
Cooling Technology	Compressor Cooling
Voltage	110V
Hot Water Temperature	185°F - 194°F
Cold Water Temperature	41-50°F