CMC Airmaster Q1 User Manual

CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN
Page 5
Section 2: Safety
Section 2.1: Safety warning
Symbols used (not necessarily all symbols are used on
the controller)
Protective Earth Terminal
The connection referred to by this symbol is to be used as
protective earth terminal
Emergency Stop
The connections referred to by this symbol are to be used
for the connection of an emergency stop switch
Danger – High Voltage.
Connections referred to by this symbol can carry a high
and dangerous voltage.
Manual sign
Indication warning the operators the manual must first be
consulted before any actions are taking place.
Warning: Risk of danger
Warning: Risk of electric shock
Warning: Risk of high pressure
Warning: Consult manual
Warning: Risk of burn
Warning risk of fire or electrical shock:
Do not install or operate the controller until you and all
personnel concerned have read and established a working
understanding of the controller inclusive of duties to be
performed while installing, operating and maintaining the
controller.
Improper use of the product may compromise the safety
and protection of the controller and its environment.
Never use the product in explosive environments.
No serviceable parts inside, return to manufacturer for
servicing or dispose according to local regulations.
Do not expose this controller to heat, fire or direct sunlight
When installing, commissioning, operating or carrying out
service or maintenance on the controller, personnel must
use relevant safe working practice and observe all
relevant local health and safety requirements and
regulations.
Lethal voltages are used within the controller and the
installation it is used in. Electricity has the potential to
cause severe personal injury or death. Isolate the source
of power to the controller when required to do so. Use
extreme caution when carrying out electrical checks.
Never remove or tamper with safety devices, guards or
insulation materials fitted to the controller or the
compressed air installation.
Compressed air has the potential to cause severe
personal injury or death. Use extreme caution when
carrying out compressed air related checks.
Hot and cold surfaces of the machinery may be exposed.
Use caution when carrying out temperature or dew point
sensor related checks.
A requirement of fault-free operation and fulfillment of any
right to claim under guarantee is that documentation is
observed.
This document is subject to changes without notice, if in
doubt, do not proceed!
It is not possible to anticipate every circumstance that
might represent a potential hazard. If the operator
employs an operating procedure, an item of equipment or
a method of working which is not specifically
recommended the user must ensure the product will not
be damaged or made unsafe and that there is no risk to
persons or property. Failure to observe safety precautions
or implement safe working practices may be considered
dangerous practice or misuse of the product.
Section 2.2: Installation
Installation work must only be carried out by a competent
person under qualified supervision. Equipped with the
correct tools and appropriate protection against electrical
hazards.
Disconnect the power before connecting the controller,
never assume power is off but always check the circuit. Be
aware that other nearby circuits can still be powered.
Do not open access panels or approach electrical
components while voltage is applied.
When hazardous live parts are exposed, use individual
protective equipment to prevent risk of shock. Use
protective gloves, fire resistant clothes and face protection
when working with live conductors. Keep fingers behind
protective barriers.
Do not use in environments where vibration or shocks are
likely to disrupt the function or compromise the safety of
the controller.
Do not wear loose clothes or jewellery like chains or
bracelets which could make contact with electrical
components.
Allow the compressor installation to cool or heat to
acceptable temperatures before attempting to install a
pressure, temperature, humidity or other type of sensor.
Always ensure any pressure within a compressed air
system is safely vented to atmosphere before attempting
to remove or install a sensor device, never assume the
compressed air system is vented but always check the air
gauge. Be aware that other nearby parts can still be hot,
cold or pressurized.
The controller should be installed in such a location as to
allow operational and maintenance access to the
installation without obstruction or hazard and to allow clear

CMC Airmaster Q1 Specifications

General

Brand	CMC
Model	Airmaster Q1
Category	Controller
Language	English