Cobra Vehicle Alarm Series 3100 User Manual

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
danub98gbb.doc
MAKE
DAEWOO
MOD.
NUBIRA
YEAR
98 →→
PETROL
DIESEL
ALARM/SIREN
POSITION
Position the compact alarms and the sirens in the engine compartment near the
left lateral headlamp. Position the modular systems and the modules under the
dashboard, drivers side.
POWER SUPPLY + 30: connect to the 2,5mm
2
RED wire located at the rear of the left lateral frame,
drivers side.
- 31: connect with an eyelet cable terminal to one of the fastening bolt of the
dashboard.
DIRECTION INDICATORS
Connect to the 1 mm
2
BLUE and LIGHT BLUE wires located in the wiring
harness and coming out of the 22 way yellow connector located on the support of
the connector holder, above the fuse box behind the left lateral frame, drivers
side.
ELECTRIC WINDOWS Positive control signal
Front window, driver’s side:
cut the BLUE wire directly outgoing from the switch of the window to the inner
drivers side door.
Front window, passenger’s side:
cut the 1,5 mm
2
LIGHT BLUE wire.
Rear window, driver’s side:
cut the 1,5 mm
2
BROWN wire.
Rear window, passenger’s side:
cut the 1,5 mm
2
GREEN wire located in the wiring harness coming out of the
drivers side door.
CENTRAL DOORS LOCKING Negative control signal
Connect to the LIGHT BLUE wires with WHITE reference located at the position
nr. 7 (lock) and the YELLOW at the position nr. 1 (unlock), in the 9 way white
connector of the central door locking unit located at the rear of the left lateral
frame, drivers side.
Note: for the vehicles without original key less entry, please refer to
diagram nr. 42 for the serie Bridge antithefts or refer to diagram nr.42A for
serie 3100 antithefts.
IMMOBILISATION POINT
The vehicle has an original equipment immobiliser that may be enabled
immediately when the switchboard is switched off.
BONNET SWITCH
Install an additional switch on the front headlamp support plate.
DOORS SWITCH
Connect to the 0,5 mm
2
WHITE wire located in the wiring harness coming out of
the 16 way white connector, on the support of the connector holder, above the
fuse box behind the left lateral frame, drivers side.
BOOT SWITCH
Connect to the 0,5 mm
2
PINK wire with BLACK reference located in the wiring
harness and coming out of the 16 way white connector located on the support
mentioned above.
X

Cobra Vehicle Alarm Series 3100 Specifications

General

Panic Mode	Yes
Keyless Entry	Yes
Starter Kill	Yes
LED Status Indicator	Yes
Remote Start	No
Shock Sensor	Yes
Security Features	Remote Control
Alarm Type	Siren
Type	Car Alarm
System Type	2-Way Security System

Summary

Vehicle Alarm Fitting Instructions

Alarm Siren Position

Positioning compact alarms and sirens in the engine compartment near the left headlamp.

Power Supply Connections

Connecting RED wire to the rear of the left lateral frame and to a dashboard fastening bolt.

Direction Indicators Wiring

Connect to BLUE and LIGHT BLUE wires in the 22 way yellow connector behind the left lateral frame.

Electric Windows Control

Wiring for positive control signal for front and rear electric windows on driver and passenger sides.

Central Doors Locking

Negative Control Signal

Connect LIGHT BLUE/WHITE (lock) and YELLOW (unlock) wires from the 9 way white connector.

Antitheft Diagrams Reference

Refer to diagram nr. 42 for Bridge antithefts or nr.42A for 3100 antithefts for specific vehicles.

Immobilisation and Switches

Immobiliser System

Vehicle has an original immobiliser that may be enabled immediately when switched off.

Bonnet Switch Installation

Install an additional switch on the front headlamp support plate.

Doors and Boot Switch Wiring

Connect WHITE wire for doors and PINK/BLACK wire for boot from the 16 way white connector.

Fitting Diagram Reference

Diagram N°42 Serie BRIDGE

Wiring diagram for negative control signal for Serie BRIDGE antitheft systems.

Diagram N°42A Serie 3100

Wiring diagram for negative control signal for Serie 3100 antitheft systems.