Coleman Somerset Pass 9230-174C User Manual

Connect Frame to Tent
– Insert one pin into the end of main tent pole
at tent corner. (illus. 3, illus. 4)
– Go to opposite end of pole and gradually
apply pressure to the pole forming an arch
until you are able to insert the pin into the
pole end.
– Repeat for second and third main poles.
(illus. 3, illus. 4) This will raise the
center of the tent.
– Assemble side and front shock-corded poles.
1
Layout & Positioning
of Tent, Pole Assembly
– Layout and position tent with front door
facing desired direction. (illus. 1)
– Unzip doors.
– Stake down tent corners only, using the
stake loops. Keep the floor taut.
(illus. 2)(Intermediate loops will be
staked later.)
– Assemble main tent poles by interlocking
shock-corded poles. (three poles)
– Insert the poles into pole sleeves.The
poles should cross forming a triangle in
the middle of tent. (illus. 1)
2
When You Are Ready
To Set Up Your Tent
– Select a level campsite clear of
rocks, branches and other hard
or sharp objects.
– Do not set up your tent under trees.
–
For best results in windy conditions,
position the end of tent into the wind.
Front Entrance Pole (Gray)
Assembled Main poles
inserted through
pole sleeves
Instructions apply to Part Number 9230-174C
illus. 1
illus. 2
Tent stake
through ring
on stake loop
illus. 4
Tent center
frame set-up
Side Pole in
position see step 3
Center poles
Part No. 9230-3521
Part No. 9230-3541
Part No. 9230-3571
illus. 3
Insert pin into pole end
Rainfly Part No.
9230-3561
(3) Main Tent Poles
(Black)
(2) Side Poles
Pet Den Pole
Part No. 9230-3591
(2) Side Rainfly Poles
Part No. 9230-3581
(1) Front Rainfly Pole
(Gray)
Part No. 9230-3562
POLE ASSEMBLY PARTS
Somerset Pass
™
17’x16’5”

Coleman Somerset Pass 9230-174C Specifications

General

Brand	Coleman
Model	Somerset Pass 9230-174C
Category	Camping Equipment
Language	English

Summary

Tent Setup Preparation

Campsite Selection

Select a level campsite clear of rocks, branches, and other hard or sharp objects.

Tent Placement

Do not set up your tent under trees. Position end of tent into wind for best results.

Tent Pole Assembly and Layout

Layout and Positioning

Position tent with front door facing desired direction, unzip doors, and stake corners.

Main Tent Pole Assembly

Assemble main tent poles by interlocking shock-corded poles and inserting into sleeves.

Frame Connection to Tent

Connecting Main Poles

Insert pins into tent corners and gradually apply pressure to form an arch.

Raising Tent Center

Repeat pole connection for second and third main poles to raise the tent center.

Adding Side and Front Poles

Inserting Poles

Insert side poles into sleeves above rear doors and front pole into sleeve above front door.

Securing Poles

Insert pins on stake loops into pole ends, apply pressure to form arches, and attach clips.

Attaching the Rainfly

Draping the Rainfly

Drape rainfly over tent frame with logos on each side, connect elastic loops to fabric loops.

Securing Rainfly Poles

Insert rainfly poles into sleeves and tips into grommets above doors, secure attachments.

Pet Room Setup

Insert pet room pole through sleeve and bend tips into grommets on stake loops.

Important Usage and Care Information

Condensation Management

Condensation can form internally; minimize by removing wet items and providing ventilation.

Storage and Maintenance

Dry tent thoroughly before storage, do not pack stakes/poles inside, avoid telescoping poles.

Safety Precautions

Keep flame/heat sources away; fabric will burn. Avoid UV damage. Remove stakes by pulling stake itself.