Conair MDCW Carousel Plus W75 - Specifications: MDCW Carousel Plus Dryers

B
A
D
Specifications: MDCW Carousel
Plus Dryers
MODEL W15 W25 W50 W75 W100
Standard hopper models* RWH14-2 RWH14-3 RWH18-6 RWH24-9 RWH24-12
Performance characteristics (with full hopper)
Air flow {SCFM} ** 7.5 12.5 25 37.5 50
Air flow {ACFM @ 250 °F } ** 10 17 34 50 67
Drying temperature All models 150 - 375 ° F {66 - 191 ° C} with options
Dew point All models -40 ° F {-40 ° C}
Standard conveying dist. ft {m} 8 {2.44} vertical; 6 {1.83} horizontal
Long distance option ft {m} 15 {4.57} vertical; 50 {15.24} horizontal
Dimensions inches {cm}
A - Height top of convey pipe 78.5 {199.4} 78.5 {199.4} 87.5 {222.3} 87.5 {222.3} 87.5 {222.3}
B - Overall width 28.5 {72.4} 28.5 {72.4} 40.5 {102.9} 40.5 {102.9} 40.5 {102.9}
C - Height to top of hopper 60.5 {153.7} 73.5 {186.7} 90.5 {229.9} 82.5 {209.6} 93.5 {237.5}
D - Depth 46 {116.8} 46 {116.8} 58 {147.3} 58 {147.3} 58 {147.3}
Outlet/inlet tube OD in. {cm} 2.5 {6.35}
Weight lbs {kg}
Standard dryer installed 500 {226.8} 550 {249.5} 600 {272.2} 675 {306.2} 750 340.2}
Voltage - Total Amps {standard/long conveying distance}
208 V/3 phase/60 Hz 16.9/20.9 16.9/20.9 21.9/25.9 22.8/26.8 NA
230 V/3 phase/60 Hz 15.3/18.9 15.3/18.9 19.8/23.4 20.6/24.2 24.9/30.5
400 V/3 phase/50 Hz ‡ 8.5/9.6 8.5/9.6 11/12.1 11.5/12.6 15.1/16.2
460 V/3 phase/60 Hz 7.7/9.5 7.7/9.5 9.9/11.7 10.3/12.1 13.4/15.2
575 V/3 phase/60 Hz 6.0/7.8 6.0/7.8 7.8/9.4 8.2/9.8 10.7/12.5
Total kilowatts † kw {std./long} 1.5/2.7 1.5/2.7 1.9/3.0 4.0/5.1 4.6/5.7
Water requirements {for optional aftercooler}
Recommended temp. § 45 ° - 85 ° F {7.2 - 29.4 ° C}
Water flow gal/min {liters/min} 1 {4.6} 2 {9.1}
Water connections NPT 3/4 in. NPT
Compressed air requirements {self-loading option only}
Compressed air 0.5 SCFH @ 80 psi
SPECIFICATION NOTES:
* Other hopper sizes are available.
** The term
SCFM stands for Standard Cubic Feet Per Minute, referenced to a pre-specified pressure, temperature and relative
humidity. In most cases, SCFM is referenced to 14.7 PSIA 68° F and 36% relative humidity. ACFM stands for Actual Cubic Feet
Per Minute, and must be supplied with a temperature reference, due to the change in air density with temperature. Because dry-
ers operate at a relatively low pressure the effects on air density are negligible.
‡ Dryers running at 50 HZ will have 17% less airflow, and a 17% reduction in material throughput.
† TOTAL kW listed at a process setpoint of 250°F {121.1°C} and a regeneration temperature of 350°F {176.7°C}.
§
Temperatures above or below the recommended levels may affect dryer performance. Tower, chiller, or municipal water
sources can be used.
Specifications may change without notice. Consult a Conair representative for the most current information.
C
(continued)
2-8 l Des cri pt io n
TPDS020-0311-REV