Copley Controls Xenus XTL Series - Ordering Guide

QTY REF DESCRIPTION MANUFACTURERS PART NUMBER
XTL-CK
Connector Kit
with
Solder Cup Connectors
for
J7 & J8
1 J1 Plug, 4 position, 7.5 mm, female Wago: 51118287 or 721-204/026-045/RN01-0000
1 J2 Plug, 4 position, 5.0 mm, female Wago: 51118008 or 721-104/026-047/RN01-0000
1 J3 Plug, 5 position, 5.0 mm, male Wago: 51111277 or 721-605/000-044/RN01-0000
1 J4 Plug, 3 position, 5.0 mm, female Wago: 51117974 or 721-103/026-047/RN01-0000
4 J1~4 Tool, wire insertion & extraction (for J1~4) Wago: 231-131
1
J7
Connector, 26 position, solder-cup High Density D-Sub Male, 26 position connector
1 Back shell, for 26 position connector Backshell for above
1
J8
Connector, 15 position, solder cup High Density D-Sub Male, 15 position connector
1 Back shell, for 15 position connector Backshell for above
CME 2
J5
CME 2 Drive Conguration Software (CD-ROM)
SER-CK RS-232 Cable Kit
Connectors & Software for CANopen Operation
XTL-NK
1
J6
D-Sub 9F to RJ-45 Adapter
1 CAN bus RJ-45 terminator
1 CAN bus network cable, 10 ft (3 m)
XTL-CV 1 D-Sub 9F to RJ-45 Adapter
XTL-NC-10 1 CAN bus Network Cable, 10 ft (3 m)
XTL-NC-01 1 CAN bus Network Cable, 1 ft (0.3 m)
XTL-NT 1 CAN bus Network Terminator
CMO CD with CMO Software
CML CD with CML Software (Note: license fee required)
Heatsink Kits for Field Installation (Optional)
XTL-HL
Heatsink Kit
Low-Prole
1 Heatsink, low-prole
1 Heatsink thermal material
4 Heatsink hardware
XTL-HS
Heatsink Kit
Standard
1 Heatsink, standard
1 Heatsink thermal material
4 Heatsink hardware
Regeneration Resistors (Optional)
XTL-RA-03 Regeneration resistor assembly (for XTL-230-18), 30 Ω
XTL-RA-04 Regeneration resistor assembly (for XTL-230-36 & XTL-230-40 models), 15 Ω
Edge Filter (Optional)
XTL-FA-01 Edge lter
Edge Filter
Connector Kit
XTL-FK
1 Plug, 4 position, 5.0 mm, female Wago: 51118008 or 721-104/026-047/RN01-0000
1 Plug, 5 position, 5.0 mm, male Wago: 51111277 or 721-605/000-044/RN01-0000
2 Tool, wire insertion & extraction (for J1~4) Wago: 231-131
Add -S to part numbers above for sin/cos feedback or add -R for resolver feedback models.
ORDERING GUIDE
XTL-230-18 Xenus XTL Servo Drive 6/18 Adc
XTL-230-36
Xenus XTL Servo Drive 12/36 Adc
XTL-230-40
Xenus XTL Servo Drive 20/40 Adc
Xenus XTL
™
DIGITAL SERVO DRIVE
for BRUSHLESS/BRUSH MOTORS
Copley Controls, 20 Dan Road, Canton, MA 02021, USA Tel: 781-828-8090 Fax: 781-828-6547
Tech Support: E-mail: sales@copleycontrols.com, Internet: http://www.copleycontrols.com Page 30 of 30
RoHS
Example: Order one Xenus drive, resolver version, 6/18 A with solder-cup connector Kit, CME 2 CD, serial cable kit and small heatsink tted at the factory:
Qty Item Remarks
1 XTL-230-18-R-HS Xenus servo drive
1 XTL-CK Connector Kit
1 CME 2 CME 2 CD
1 SER-CK Serial Cable Kit
Note: The heatsink can be tted at the factory by adding an “-HS” or “-HL” to the drive part number to specify the standard or low-prole type. For tting a
heatsink to an drive in the eld, complete kits are available (XTL-HS and XTL-HL). These kits contain the heatsink, mounting hardware, and dry-lm interface.
Rev 4.03_mo 08/17/2009
Note: Specications are subject to change without notice
ACCESSORIES