Corghi ERCO 500 - User Manual

Questions and Answers

K
Krystal OwensAug 16, 2025
What to do if my Corghi ERCO 500 Lifting Systems lift does not work?
- A
  Alyssa ReyesAug 16, 2025
  If your Corghi Lifting Systems lift isn't working, there are several potential causes: * The main switch might not be turned on, so ensure it is. * There might be no power; check and restore power if necessary. * Electrical wires could be disconnected, requiring replacement. * Blown fuses could be the issue, so replace them. * A faulty printed circuit board could be the problem, requiring replacement.
S
Sandra StevensAug 19, 2025
Why does my Corghi Lifting Systems lift not raise?
- J
  Justin GeorgeAug 19, 2025
  If your Corghi Lifting Systems lift isn't raising, consider these potential causes: * Incorrect motor direction of rotation: Interchange the two phases on the main switch. * Insufficient oil in the hydraulic unit: Add hydraulic oil. * Faulty UP button: Check the UP button and its connection; replace if needed. * Lowering valve not closing: Check and clean the valve if dirty, or replace it if faulty. * Dirty suction pump filter: Check and clean the filter if needed. * Faulty pump: Check the pump and replace it if necessary.
W
William ThomasAug 22, 2025
What to do if my Corghi ERCO 500 Lifting Systems lift does not lower when the DOWN button is pressed?
- C
  ccoleAug 22, 2025
  If the Corghi Lifting Systems lift doesn't lower when you press the DOWN button, it could be due to: * A jammed locking solenoid valve: Verify if it is powered and check magneto for damage (replace if disconnected or blown). * A faulty DOWN button: Replace the DOWN button. * A printed circuit board that does not operate properly: Replace the printed circuit board.
J
Jessica MossAug 25, 2025
Why is the lifting capacity of my Corghi ERCO 500 Lifting Systems not sufficient?
- A
  Adam CarneyAug 26, 2025
  If the lifting capacity of your Corghi Lifting Systems is insufficient, it could be due to: * Oil leakages in the hydraulic circuit: Check the circuit for any leakage. * Exceeding oil into hydraulic circuit: Push lowering button and discharging button simultaneously.
L
ljohnsonAug 28, 2025
What to do if my Corghi Lifting Systems platforms do not stop in standing position?
- J
  James SmithAug 28, 2025
  If the platforms of your Corghi Lifting Systems do not stop in the standing position, the issue might be: * Leakage in the hydraulic pipelines: Check connections for proper tightening and tubes for damage (replace if damaged). * Faulty hydraulic cylinders: Check and replace if needed (at least two cylinders must be faulty to cause this issue). * Air in the hydraulic system: Bleed the hydraulic system.
L
Lindsay EvansAug 31, 2025
How to fix unsynchronized lifting in Corghi ERCO 500?
- E
  Elizabeth MatthewsAug 31, 2025
  If lifting is not synchronized in your Corghi Lifting Systems, it could be because the safety height limit switch does not work. Check the limit switch and replace it if needed.
B
bennettmeghanSep 3, 2025
What to do if Corghi ERCO 500 lift does not lower smoothly?
- M
  Michael GibsonSep 3, 2025
  If your Corghi Lifting Systems lift does not lower smoothly, it could be due to leakages or the presence of air in the hydraulic circuit. Bleed the hydraulic system to resolve this.
M
maryrobertsSep 6, 2025
What to do if Corghi ERCO 500 lift does not stop at safety height?
- M
  Melissa HernandezSep 6, 2025
  If the Corghi Lifting Systems lift does not stop at the safety height, it is likely that the maximum height limit switch is not working. Check the limit switch and replace it if needed.
B
Brian OrrSep 9, 2025
What to do if my Corghi Lifting Systems lift does not lower when the DOWN button is pressed (without load)?
- K
  Kayla WhiteSep 9, 2025
  If your Corghi Lifting Systems lift doesn't lower when the DOWN button is pressed (without a load), the lowering solenoid valve may not be working properly. Verify if it is powered and check magneto for damage (replace if disconnected or blown).
S
samantha13Sep 12, 2025
Why do the lowering and locking solenoid valves stay opened on my Corghi ERCO 500 Lifting Systems?
- A
  alexandracraigSep 12, 2025
  To address the issue of the lowering and locking solenoid valves staying opened on your Corghi Lifting Systems, verify that solenoid valve sliders are not blocked.