22 23
4 If connecting the drain line to a garbage disposal, make sure that the drain plug has been removed. Your dishwasher
will not drain if the plug is left in place.
Step 15: Performing a pre-test check
Review this list after installing your dishwasher to avoid problems or charges for a service call not covered by your
warranty.
• Make sure that power is turned OFF.
• Open the door and remove all foam and paper packaging.
•Locate the User Guide in the literature package.
•Read the User Guide for operating instructions.
• Check the door opening and closing. If the door does not open and close freely, or tends to fall, check the spring
adjustments. See Step 1: Check the door balance
on page 10
.
• Make sure that the wiring is secure under the dishwasher and not pinched or in contact with door springs or other
components. See Step 9: Position the dishwasher under the countertop
on page 16
.
• Check the door alignment with the tub. If the door hits the tub, level the dishwasher. See Step 10: Level the dishwasher
on page 16
.
• Pull the lower rack out about half way. Make sure that it does not roll back or forward on the door. If the rack moves,
adjust the leveling legs. See Step 10: Level the dishwasher
on page 16
.
• Check the door alignment with the cabinet. If the door hits the cabinet, reposition or relevel the dishwasher. See Step
10: Level the dishwasher
on page 16
.
• Make sure that water supply and drain lines are not kinked or in contact with other components. Any contact with the
motor or dishwasher frame could cause a noise. See Step 8: Slide the dishwasher partially into the cabinet
on page 15
.
• Turn on the sink hot water faucet and verify the water temperature. Incoming water temperature must be between
120°F and 150°F. A minimum of 120°F temperature is required for best wash performance. See Preparing the hot water
line
on page 9
.
• Add a half gallon (2 l) of water to the bottom of the dishwasher to lubricate the pump seal.
• Turn on the water supply. Check for leaks. Tighten connections if needed.
• Remove any protective film (if present) from the control panel and door.
You’ll need:
Phillips screwdriver
Screw-type
hose clamps
Coupler for
extending drain line
(if applicable)
Step 16: Wet testing the dishwasher
1 Turn on the power supply (or plug the power cord into the outlet, if equipped).
2 Turn on your dishwasher (refer to the User Guide for instructions).
3 Close the door, select the Rinse only cycle, and press START/Cancel.
4 Make sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and
power are turned on.
5 Check for leaks under the dishwasher. If a leak is found, turn the power supply off, then tighten connections. Restore
power after the leak is corrected.
6 Check for leaks around the door. A leak around the door could be caused by door rubbing or hitting against adjacent
cabinetry. Reposition the dishwasher if necessary. See “Step 9: Position the dishwasher under the countertop on page
16” on page 16.
7 When the dishwasher is draining, check the drain lines. If leaks are found, turn power off at the breaker and correct
plumbing as necessary.
8 Restore the power after corrections are made. See “Step 12: Connecting the water supply line on page 19” on page 19.
9 Open the dishwasher door and make sure that most of the water has drained. If not, check that the disposer plug has
been removed and/or the air gap is not plugged. See “Step 13: Connecting the drain hose on page 19” on page 19. Also
check the drain line for kinking.
10 Run the dishwasher through another fill and drain cycle. Check for leaks and correct if required.
Step 17: Replacing the toekick
• Place the toekick against the legs of the dishwasher. The slots should align with the toekick bracket screw holes. Allow
the toekick to touch the floor. Install the toekick screws.
Note:
Make sure that you install the toekick in the correct direction. The toekick should be aligned correctly with the junction box.
You’ll need:
To Next Page
Loading...
Need help?
General