Craftsman 139.53985D User Manual

1/2 HP
GARAGE DOOR OPENER
ABRIDOR DE PUERTA DE COCHERA DE
For Residential Use Only/Sólo para uso residencial
Models/Modelos • 139.53985D
®
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A
www.sears.com/craftsman
Owner’s Manual/Manual Del Propietario
ENGLISH ESPAÑOL
Read and follow all safety rules
and operating instructions before
first use of this product.
Fasten the manual near the garage
door after installation.
Periodic checks of the opener are
required to ensure safe operation.
Leer y seguir todas las reglas de
seguridad y las instrucciones de
operación antes de usar este
producto por primera vez.
Guardar este manual cerca de la
puerta de la cochera.
Se deben realizar revisiones
periódicas del abridor de puertas
para asegurar su operación
segura.

Craftsman 139.53985D Specifications

General

Brand	Craftsman
Model	139.53985D
Category	Garage Door Opener
Language	English

Summary

Assembling the Rail and Trolley

Rail Assembly and Trolley Installation Steps

Attaching Rail to Motor Unit

Securing the Rail Assembly to the Motor Unit

Installing the Idler Pulley

Idler Pulley Mounting and Chain Routing

Installing the Chain and Cable

Routing and Connecting the Chain/Cable to Trolley

Detailed steps for routing the chain or cable around pulleys and connecting it to the trolley.

Final Chain Tightening

Adjusting Chain Tension for Proper Operation

Critical Installation Safety Instructions

Essential Safety Guidelines Before Installation

Critical warnings and guidelines to follow before and during opener installation.

Determining Header Bracket Location

Wall Mounting Location for Header Bracket

Instructions for locating and marking the header bracket position for wall mounting.

Ceiling Mounting Location for Header Bracket

Guidelines for determining header bracket placement when mounting to the ceiling.

Installing the Header Bracket

Securing the Header Bracket to the Wall

Steps to secure the header bracket to the wall structure using provided hardware.

Securing the Header Bracket to the Ceiling

Steps to secure the header bracket to the ceiling structure using provided hardware.

Attaching the Rail to the Header Bracket

Connecting the Rail Assembly to the Header Bracket

Positioning the Garage Door Opener Unit

Positioning Opener for Sectional Doors with Track

Positioning Opener for One-Piece Doors Without Track

Hanging the Garage Door Opener Unit

Securing Opener to Structural Supports via Hanging Brackets

Installing the Wall-Mounted Door Control

Wiring and Mounting the Door Control Panel

Door Control Safety Precautions and Connections

Attaching the Emergency Release Rope and Handle

Securing the Manual Door Release Mechanism

Electrical Requirements for Opener Installation

Ensuring Proper Grounding and Wiring Safety

Essential electrical safety guidelines and proper grounding for the opener.

Installing the Safety Reversing Sensor (Protector System)

Mounting and Aligning Safety Reversing Sensors

Procedures for mounting and aligning the safety reversing sensors for obstruction detection.

Installing Safety Sensor Brackets

Mounting Sensors on Garage Door Tracks

Wall and Floor Mounting Options for Sensors

Mounting and Wiring Safety Reversing Sensors

Connecting Safety Sensor Wires to Opener

Aligning Safety Reversing Sensors for Operation

Fastening the Door Bracket to the Garage Door

Reinforcement for Lightweight Garage Doors

Sectional Door Bracket Installation Procedure

Installing the Door Bracket on One-Piece Doors

Connecting Door Bracket for One-Piece Doors

Connecting the Door Arm to the Trolley

Sectional Door Arm Connection to Trolley

Assembling and Connecting Door Arm for One-Piece Doors

One-Piece Door Arm Assembly and Trolley Connection

Adjusting Travel Limits

Setting the UP Travel Limit for Opener

Procedure for adjusting the opener's fully open position limit.

Setting the DOWN Travel Limit for Opener

Procedure for adjusting the opener's fully closed position limit.

Adjusting Door Opener Force Settings

Adjusting Down (Close) Force Control

How to adjust the force required for the door to close and reverse properly.

Adjusting Up (Open) Force Control

How to adjust the force required for the door to open completely and stop.

Testing the Safety Reversal System

Performing the Safety Reversal System Test

How to test the door's ability to reverse upon encountering an obstruction.

Testing the Protector System (Safety Sensors)

Verifying Safety Sensor Alignment and Functionality

How to test that the safety reversing sensors are correctly installed and functioning.

Operating Your Garage Door Opener

Critical Safety Guidelines for Opener Operation

Critical safety instructions for operating the garage door opener and door.

Using the Wall-Mounted Door Control

Opening the Garage Door Manually

Disconnecting and Reconnecting the Trolley for Manual Use

Troubleshooting Common Garage Door Opener Problems

Diagnosing Door Closure or Light Blink Issues

Addressing Remote Control Activation Failures

Interpreting Opener Diagnostic Codes

Understanding 1 Flash Diagnostic Code

Understanding 4 Flashes Diagnostic Code

Programming Garage Door Opener Remotes

Adding or Reprogramming Hand-Held Remote Controls

Step-by-step guide to program new or existing remote controls to the opener.

Erasing All Programmed Remote Control Codes

How to clear all previously programmed remote control codes from the opener.

Programming Keyless Entry Systems

Adding or Reprogramming Keyless Entry PINs

Instructions for setting up or changing the PIN for the Keyless Entry system.