Craftsman 247.772460 - User Manual

Other manuals for Craftsman 247.772460

Parts List8 pages

Questions and Answers

T
Taylor DodsonAug 17, 2025
Why won't my Craftsman Lawn Mower engine start?
- M
  Matthew JohnsonAug 17, 2025
  There are several reasons why your Craftsman Lawn Mower engine might fail to start: * The air cleaner might be dirty. * The engine may need priming, so push the primer bulb three times. * The fuel tank could be empty; refill it with clean, fresh gasoline. * The gasoline in the tank might be stale; drain it and refill with fresh gasoline. * The spark plug wire might be disconnected; connect it to the spark plug. * The spark plug might be fouled; clean, adjust the gap, or replace it.
C
crystalsosaAug 20, 2025
Why does my Craftsman 247.772460 Edger engine fail to start?
- D
  despinozaAug 20, 2025
  Your Craftsman Edger engine may fail to start due to several reasons: the blade control may be disengaged (engage the blade control), the spark plug boot may be disconnected (connect the wire to the spark boot), the fuel tank may be empty or contain stale fuel (fill the tank with clean, fresh gasoline), the spark plug may be faulty (clean, adjust the gap, or replace it), the engine may be flooded (wait a few minutes to restart), or the fuel line may be blocked. For blocked fuel line contact your Sears Parts & Repair Center to have fuel line cleaned.
A
Alexandra WhiteAug 22, 2025
Why is the drive-belt slipping on my Craftsman Edger?
- J
  jessetaylorAug 23, 2025
  If the drive belt on your Craftsman Edger is slipping, it is likely worn or stretched. Replace the drive belt.
L
Lisa BernardAug 26, 2025
What to do if my Craftsman Lawn Mower engine runs erratically?
- J
  Jeffrey HamiltonAug 26, 2025
  If your Craftsman Lawn Mower engine is running erratically, it could be due to: * A loose spark plug wire; connect and tighten it. * Stale fuel in the gasoline tank; drain the gasoline and refill the tank with clean, fresh gasoline. * A plugged vent in the gas cap; clear any debris from the vent. * Water or dirt in the fuel system; drain the fuel tank and refill it with fresh fuel.
D
David PetersonAug 28, 2025
Why is my Craftsman Lawn Mower engine overheating?
- E
  Erik JeffersonAug 28, 2025
  Your Craftsman Lawn Mower engine may be overheating due to: * Low engine oil level; fill the crankcase with the proper oil. * Restricted airflow; clean the area around the engine’s cooling fins. * A dirty air filter; replace the engine’s air filter.
M
Marie SchwartzAug 31, 2025
Why does the drive-belt slip on my Craftsman Lawn Mower?
- C
  Collin LeeAug 31, 2025
  The drive belt on your Craftsman Lawn Mower may be slipping because the belt is worn or stretched. Replace the drive belt.
J
Jamie HoustonSep 2, 2025
Why does my Craftsman 247.772460 Edger engine run erratically?
- R
  richardchungSep 3, 2025
  An erratic running engine on your Craftsman Edger can be caused by a loose spark plug boot (connect and tighten the spark plug boot), stale fuel (fill the tank with clean, fresh gasoline), a plugged vent in the gas cap (clear the vent), or water/dirt in the fuel system (run the engine until it stops from lack of fuel, then refill with fresh fuel). A dirty air cleaner may also be the cause. For blocked fuel line contact your Sears Parts & Repair Center to have fuel line cleaned.
E
Ebony ContrerasSep 5, 2025
What to do if my Craftsman 247.772460 engine overheats?
- N
  newtonamandaSep 6, 2025
  If your Craftsman Edger engine is overheating, it could be due to a low engine oil level (fill the crankcase with the proper oil) or restricted airflow (clean the area around and on top of the engine).
C
Carlos EvansSep 8, 2025
What to do if my Craftsman 247.772460 idles poorly?
- E
  Emily WuSep 8, 2025
  Poor idling in your Craftsman Edger can occur if the spark plug is fouled, faulty, or the gap is too wide (reset the gap to .030” or replace the spark plug). A dirty air cleaner may also be the cause.
H
Heather VegaSep 12, 2025
Why does my Craftsman 247.772460 have excessive vibration?
- A
  Adrian OwensSep 12, 2025
  Excessive vibration in your Craftsman Edger is often due to a bent or damaged edger blade (replace the edger blade). It can also be from a bent or damaged blade spindle. Contact your Sears Parts & Repair Center to have unit inspected.