Craftsman 247.887200 - User Manual

Questions and Answers

M
Morgan WernerAug 8, 2025
Why won't my Craftsman 247.887200 Snow Blower start?
- B
  Brittany KirbyAug 8, 2025
  There are several reasons why your Craftsman Snow Blower might not be starting. It could be due to an empty or stale fuel tank, which requires filling with fresh gasoline. A blocked fuel line needs cleaning. Ensure the key is fully inserted. Check that the spark plug wire is connected, and the spark plug isn't faulty (clean, readjust the gap, or replace it). Also, make sure you've primed the engine by pushing the primer button three times, or if you've over-primed it, wait ten minutes before trying again. If you're using the electric start, verify the extension cord is properly connected to both the snow blower and a grounded outlet.
M
Michael ZimmermanAug 12, 2025
Why is my Craftsman 247.887200 Snow Blower losing power?
- D
  David SimpsonAug 12, 2025
  A loss of power in your Craftsman Snow Blower could be due to a loose spark plug wire; make sure it's firmly connected. Another possible cause is a plugged vent in the gas cap; clear the vent to resolve this.
R
rbeckAug 16, 2025
What to do if the auger continues to rotate on my Craftsman 247.887200?
- B
  Bridget BushAug 16, 2025
  If the auger continues to rotate on your Craftsman Snow Blower, the auger control cable is likely out of adjustment. Refer to the Service and Maintenance section to adjust the auger control cable.
D
Diane SanchezAug 20, 2025
What to do if my Craftsman 247.887200 Snow Blower won't throw snow?
- F
  frenchlindaAug 21, 2025
  If your Craftsman Snow Blower isn't discharging snow, the chute assembly might be clogged; stop the engine, disconnect the spark plug wire, and clean the chute and auger housing with a tool or stick. There could also be a foreign object lodged in the auger, so stop the engine, disconnect the spark plug wire, and remove the object. Also, examine the auger control cable, it may need adjustment. Finally, the auger belt might be loose or damaged, requiring replacement.
J
Jesse MclaughlinAug 25, 2025
How to fix erratic engine RPM on my Craftsman Snow Blower?
- M
  Maria MaddoxAug 26, 2025
  Erratic engine RPMs in your Craftsman Snow Blower can occur for several reasons. First, ensure the choke control is in the RUN position, not engaged. A blocked fuel line or stale fuel can also cause this, so clean the fuel line and refill with fresh gasoline. Water or dirt in the fuel system might be the culprit; run the engine until it stops, then refill with fresh fuel. If these steps don't resolve the issue, the carburetor might need adjustment, in which case you should contact a Sears Service Center. An over-governed engine can also cause this issue, and you should contact a Sears Service Center.
E
Erin ChangAug 29, 2025
Why is my Craftsman 247.887200 Snow Blower not self-propelled?
- R
  Rachel MendezAug 29, 2025
  If your Craftsman Snow Blower isn't self-propelling, the auger control cable may be out of adjustment; adjust it as shown in the Service and Maintenance section. Alternatively, the auger drive belt could be loose or damaged, requiring replacement.
D
Donna HaynesSep 2, 2025
What causes excessive vibration in my Craftsman 247.887200?
- A
  Anthony DominguezSep 2, 2025
  Excessive vibration in your Craftsman Snow Blower is often due to loose parts or a damaged auger. Immediately stop the engine and disconnect the spark plug wire. Check for any damage and tighten all bolts and nuts. If the problem continues, it's best to take your snow thrower to a Sears Service Center.

Craftsman 247.887200 Specifications

General

Engine Type	4-cycle OHV
Start Type	Electric/Recoil
Product Type	Two-stage Snow Blower
Drive Type	Self-propelled
Number of Forward Speeds	6
Number of Reverse Speeds	2
Engine Displacement	208cc
Chute Control	Remote
Auger Material	Steel
Wheel Size	13 inches