EasyManua.ls Logo

Craftsman 247.887801 - User Manual

Craftsman 247.887801
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Sears Brands Management Corporation, Hoffman Estates, IL 60179, U.S.A.
Visit our website: www.craftsman.com
CAUTION: Before using
this product, read this
manual and follow all
safety rules and operating
instructions.
Operator’s Manual
21” SNOW THROWER
Model No. 247.887801
• SAFETY
• ASSEMBLY
• OPERATION
• MAINTENANCE
• PARTS LIST
• ESPAÑOL
7/19/2012
FORM NO. 769-06194F
®

Table of Contents

Questions and Answers

  • B
    bakerjoshuaAug 10, 2025
    Why does my Craftsman 247.887801 Snow Blower engine fail to start?
    • R
      Rodney RobertsAug 10, 2025
      Your Craftsman Snow Blower might not be starting due to several reasons: * The fuel tank could be empty or the fuel stale; in this case, fill the tank with clean, fresh gasoline. * The key may not be fully inserted; ensure it is inserted all the way. * The spark plug wire might be disconnected; connect it to the spark plug. * The spark plug could be faulty; try cleaning it, readjusting the gap, or replacing it. * The engine may not be primed; push the engine primer button three times. * The engine could be flooded from excessive priming; wait at least ten minutes before attempting to start it.
  • M
    Melanie HoldenAug 15, 2025
    Why is my Craftsman 247.887801 engine running erratically?
    • R
      Richard BooneAug 15, 2025
      An erratic engine in your Craftsman Snow Blower can stem from a few issues: * The engine might be running on choke; move the choke control to the RUN position. * There might be water or dirt in the fuel system; run the engine until it stops, then refill with fresh fuel.
  • T
    terrellwilliamAug 20, 2025
    Why Craftsman 247.887801 Snow Blower has loss of power?
    • S
      Sarah GreenAug 20, 2025
      A loss of power in your Craftsman Snow Blower can be caused by: * A loose spark plug wire; firmly connect the spark plug wire. * A plugged vent in the gas cap; clear the vent.
  • G
    Gary BrownAug 26, 2025
    How to fix Craftsman Snow Thrower that fails to self-propel?
    • P
      paul81Aug 26, 2025
      If your Craftsman snow thrower isn't self-propelling: * The auger control cable may be out of adjustment; adjust it as shown in the Service and Maintenance section. * The auger drive belt might be loose or damaged; replace it.
  • J
    James DodsonAug 30, 2025
    What to do if my Craftsman Snow Blower unit fails to discharge snow?
    • A
      Aaron GilbertAug 30, 2025
      If your Craftsman snow blower isn't discharging snow, here's what you can do: 1. Stop the engine and disconnect the spark plug wire, then clean the chute assembly and the inside of the auger housing using a clean-out tool or stick, as the chute assembly may be clogged. 2. Immediately stop the engine and disconnect the spark plug wire to remove any foreign objects lodged in the auger. 3. Adjust the auger control cable. 4. Replace the auger belt if it is loose or damaged.
  • D
    Daniel WuSep 4, 2025
    What to do if Craftsman 247.887801 Snow Blower has excessive vibration?
    • H
      hawkinslaurieSep 4, 2025
      If your Craftsman snow thrower is vibrating excessively, immediately stop the engine and remove the key. Check for any loose parts or damage to the auger. Tighten all bolts and nuts, and repair as needed. If the problem continues, it is recommended to contact a Sears Service Center.

Craftsman 247.887801 Specifications

General IconGeneral
Engine208cc
Engine Displacement208cc
Chute ControlManual
Auger MaterialSteel
Warranty2-year limited
Clearing Width24 inches
Intake Height21 inches
Engine Type4-Cycle
Starter TypeRecoil

Related product manuals