Craftsman 247.88794 Series

Questions and Answers

J
James ReedAug 20, 2025
Why won't my Craftsman Snow Blower engine start?
- V
  Virginia GillespieAug 20, 2025
  There are several reasons why your Craftsman Snow Blower engine might not start. First, ensure the choke control is in the CHOKE position. Check that the spark plug wire is securely connected to the spark plug. The spark plug itself may be faulty and require cleaning, gap adjustment, or replacement. The fuel tank may be empty or contain stale fuel, so fill it with fresh gasoline. Make sure you prime the engine as instructed in the Operation section. Ensure the safety key is fully inserted into the switch. If your model has an electric start button, verify the extension cord is properly connected to both the snow blower and a grounded AC outlet.
A
Amanda FletcherAug 22, 2025
Why does my Craftsman Snow Blower engine fail to start?
- A
  Andrea KleinAug 22, 2025
  There are several reasons why your Craftsman Snow Blower might not be starting: * The choke control may not be in the CHOKE position, so move it accordingly. * The spark plug wire might be disconnected; ensure it's connected. * The spark plug could be faulty and needs cleaning, gap adjustment, or replacement. * The fuel tank might be empty or contain stale fuel; refill with fresh gasoline. * The engine may not be primed; prime it as instructed in the Operation section. * The safety key might not be inserted; insert it fully into the switch. * The extension cord might not be connected (if your model has an electric start button); connect it to a grounded outlet.
J
Joshua VegaAug 25, 2025
Why is my Craftsman Snow Blower engine running erratically?
- T
  Travis MartinAug 25, 2025
  If your Craftsman Snow Blower engine is running erratically, it could be due to several factors. First, ensure that the choke control is not engaged (move it to the RUN position). Stale fuel can also cause this issue, so try filling the tank with fresh gasoline. Water or dirt in the fuel system might be the culprit; in this case, drain the fuel tank by running the engine until it stops, then refill with fresh fuel. In some cases, the carburetor may be out of adjustment or the engine may be over-governed, and you will need to contact a Sears or other qualified service dealer for repair.
F
floreslisaAug 26, 2025
What to do if my Craftsman Snow Blower won't throw snow?
- L
  Loretta BrooksAug 26, 2025
  If your Craftsman Snow Blower is not discharging snow, the chute assembly might be clogged. Stop the engine immediately, disconnect the spark plug wire, and then clean the chute assembly and the inside of the auger housing using a clean-out tool. Another reason could be a foreign object lodged in the auger; in this case, stop the engine, disconnect the spark plug wire, and remove the object with the clean-out tool. Also, the auger cable may need adjustment, or the auger belt may be loose or damaged. Finally, check if the shear pins are sheared and replace them if necessary. Refer to the Operation section for instructions.
W
Wayne BeasleyAug 27, 2025
What to do if my Craftsman Snow Blower loses power?
- E
  Elizabeth LangAug 28, 2025
  If your Craftsman Snow Blower is losing power, check the following: * Ensure the spark plug wire is connected and tightened. * Make sure the gas cap vent hole isn't plugged; remove any ice or snow to clear it.
G
gjohnsonAug 29, 2025
Why is my Craftsman 247.88794 Snow Blower losing power?
- W
  William CaseyAug 30, 2025
  If your Craftsman Snow Blower is losing power, check that the spark plug wire is securely connected and tightened. Also, the gas cap vent hole may be plugged with ice or snow. Remove any obstructions to ensure the vent hole is clear.
S
Steven CurrySep 1, 2025
Why is my Craftsman 247.88794 Snow Blower plowing snow instead of blowing it?
- W
  warrenmanuelSep 1, 2025
  If your Craftsman Snow Blower is plowing snow instead of blowing it, try increasing the ground speed and always operate the engine at FULL throttle, especially in wet or slushy snow that is 1-3” deep. Another possible reason is sheared shear pins, which should be replaced.
R
Ruben OliverSep 3, 2025
Why is my Craftsman Snow Blower vibrating so much?
- C
  Cassandra JuarezSep 3, 2025
  If your Craftsman Snow Blower is vibrating excessively, stop the engine immediately and disconnect the spark plug wire. Then, tighten all bolts and nuts. If the vibration continues, have the unit serviced by a Sears Parts & Repair Center.
R
robert00Sep 5, 2025
Why is my Craftsman 247.88794 Snow Blower not moving forward?
- M
  Michele CampbellSep 5, 2025
  If your Craftsman Snow Blower is not propelling itself, the drive cable may need adjustment. Refer to the Service and Maintenance section for instructions on how to adjust the drive control cable. Alternatively, the drive belt may be loose or damaged, or the friction wheel may be worn. In either of these cases, contact a Sears or other qualified service dealer for repair, ensuring they use an identical replacement part.
J
Joseph NguyenSep 7, 2025
How to fix a Craftsman Snow Blower chute that won't rotate?
- K
  Kimberly StewartSep 7, 2025
  If the chute on your Craftsman Snow Blower does not easily rotate 180-200 degrees, it may be assembled incorrectly. Disassemble the chute control and reassemble it as directed in the Assembly section.

Craftsman 247.88794 Series Specifications

General

Engine Type	4-Cycle OHV
Engine Displacement	208cc
Number of Forward Speeds	6
Number of Reverse Speeds	2
Auger Material	Steel
Chassis Material	Steel
Clearing Width	24 inches
Intake Height	21 inches
Start Type	Recoil
Throw Distance	40 feet