Craftsman 31AM62EE799 User Manual (English)

Questions and Answers:

L
Lori RiceAug 6, 2025
Why won't my Craftsman 31AM62EE799 Snow Blower engine start?
- M
  maureenhawkinsAug 6, 2025
  Your Craftsman Snow Blower engine may fail to start due to several reasons: * The choke control might not be in the ON position; if so, move it to the ON position. * The spark plug wire could be disconnected; connect it to the spark plug. * The spark plug might be faulty; clean, adjust the gap, or replace it. * The fuel tank may be empty or contain stale fuel; fill it with clean, fresh gasoline. * The engine may not be primed; prime it as instructed in the Operation Section. * The safety key might not be inserted; insert it fully into the switch.
T
Troy CortezAug 11, 2025
What to do if my Craftsman 31AM62EE799 Snow Blower unit fails to discharge snow?
- R
  Richard SanchezAug 11, 2025
  If your Craftsman Snow Blower fails to discharge snow, here are some possible solutions: * The chute assembly might be clogged. Stop the engine immediately, disconnect the spark plug wire, and clean the chute assembly and inside of the auger housing with a clean-out tool or a stick. * A foreign object may be lodged in the auger. Stop the engine immediately, disconnect the spark plug wire, and remove the object from the auger with a clean-out tool or a stick. * The auger cable might need adjustment. Adjust the auger control cable according to the Assembly section. * The auger belt could be loose or damaged. Replace the auger belt, referring to the Service and Maintenance section. * The shear pins might be sheared. Replace them with new shear pins.
B
Benjamin SnowAug 16, 2025
Why does my Craftsman 31AM62EE799 engine run erratically?
- C
  cjonesAug 16, 2025
  An erratic running Craftsman Snow Blower engine can be caused by: * The engine running on CHOKE; move the choke control to the OFF position. * Stale fuel; replace with clean, fresh gasoline. * Water or dirt in the fuel system; drain the fuel tank and refill with fresh fuel. * The carburetor being out of adjustment; in this case, contact your Sears Parts & Repair Center.
J
Jeffrey SimsAug 20, 2025
What to do if my Craftsman 31AM62EE799 loses power?
- K
  Kevin HoganAug 20, 2025
  If your Craftsman Snow Blower is losing power: * Check the spark plug wire and ensure it is connected and tightened. * Inspect the gas cap vent hole for blockage from ice or snow, and clear it to ensure proper ventilation.
D
Darryl ThompsonAug 26, 2025
How to fix excessive vibration in my Craftsman Snow Blower?
- J
  Jennifer HesterAug 26, 2025
  If your Craftsman Snow Blower is vibrating excessively, stop the engine immediately, disconnect the spark plug wire, and check for loose parts or a damaged auger. Tighten all bolts and nuts. If the vibration continues, have the unit serviced by a Sears Parts & Repair Center.
D
Donald AndersonAug 31, 2025
Why won't my Craftsman Snow Blower propel itself?
- A
  Andrew WestAug 31, 2025
  If your Craftsman Snow Blower isn't moving on its own, it could be due to: * The drive cable needing adjustment; adjust the drive control cable as described in the Service and Maintenance section. * A loose or damaged drive belt; replace the drive belt, consulting the Service and Maintenance section. * A worn friction wheel; replace the friction wheel.

Craftsman 31AM62EE799 Specifications

General

Brand	Craftsman
Model	31AM62EE799
Category	Snow Blower
Language	English

Summary

Operator's Manual

CRAFTSMAN 24" SNOW THROWER

Product title and model identification.

Model No. 247.88955

Specific model number of the snow thrower.

Important Safety Notice

Key safety warnings and precautions before initial use.

WARRANTY STATEMENT

CRAFTSMAN LIMITED WARRANTY

Details the warranty terms and conditions for the snow thrower.

PRODUCT SPECIFICATIONS

Lists key product specifications like engine oil type and capacity.

SAFETY INSTRUCTIONS

General Safety Warnings

Explanation of safety symbols and general precautions for safe operation.

CALIFORNIA PROPOSITION 65

Specific legal compliance notice regarding engine exhaust chemicals.

Preparation and Training

Guidance on machine preparation and operator training before use.

SAFETY INSTRUCTIONS

Safe Gasoline Handling

Critical safety instructions for handling and storing gasoline.

Safe Operation Practices

Guidelines for safe operation, including terrain and debris management.

SAFETY INSTRUCTIONS

Maintenance and Storage Safety

Safety precautions for machine maintenance and off-season storage.

Engine Modification Warning

Warning against modifying the engine's governor or settings.

Spark Arrestor Information

Information regarding the spark arrestor requirement for safe operation.

SAFETY INSTRUCTIONS

SAFETY SYMBOLS

Description and meaning of all safety symbols used in the manual.

SAFETY LABELS

DANGER Labels

Illustrations and explanations of critical DANGER safety labels on the machine.

ASSEMBLY

Unpacking and Initial Assembly

Steps for removing the snow thrower from its carton and initial handle assembly.

Loose Parts Identification

List and identification of included loose parts before assembly.

ASSEMBLY

Chute Assembly and Control

Instructions for assembling the chute and connecting its directional control.

ASSEMBLY

Setup and Adjustments

Setting up the chute clean-out tool, checking tire pressure, and adjusting skid shoes.

ASSEMBLY

Chute Angle Adjustment

Procedure for adjusting the angle of the chute assembly.

Auger Control Adjustment

Critical adjustment procedure for the auger control cable for safety.

OPERATION

Controls Overview

Identification and basic function of the snow thrower's main controls.

OPERATION

Engine Controls

Explanation of throttle, primer, and starter controls for engine operation.

Drive and Auger Controls

How to engage and disengage the drive wheels and auger system.

Chute and Skid Shoe Controls

Operation of the chute directional control and positioning of skid shoes.

OPERATION

Pre-Start Procedures

Steps before starting the engine, including chute cleaning, oil, and fuel checks.

OPERATION

Starting Procedures

Detailed instructions for starting the engine using electric or recoil starter.

Stopping and Engaging

Procedures for stopping the engine and engaging drive/auger systems.

REPLACING SHEAR PINS

Instructions for replacing shear pins for auger protection.

SERVICE AND MAINTENANCE

Engine Maintenance

General guidelines for engine upkeep and oil level checks.

SERVICE AND MAINTENANCE

Spark Plug Maintenance

Procedure for checking, cleaning, and gapping the spark plug.

Gear Shaft Lubrication

Instructions for lubricating the gear shaft for proper function.

SERVICE AND MAINTENANCE

Component Maintenance

Maintenance for wheels, chute control, and auger shaft.

Shave Plate and Skid Shoes

Checking and replacing the shave plate and skid shoes.

Cable Adjustments

Adjusting the shift cable and drive control cable for proper operation.

SERVICE AND MAINTENANCE

Cable Adjustments (cont.)

Further steps for adjusting the drive control cable.

Bracket Adjustments

Procedure for adjusting the chute bracket for chute engagement.

Belt Replacement

Instructions for replacing the auger belt.

SERVICE AND MAINTENANCE

Auger Belt Replacement

Steps for removing and replacing the auger belt.

SERVICE AND MAINTENANCE

Auger Belt Replacement (cont.)

Continuation of auger belt replacement steps.

Drive Belt Replacement

Instructions for removing and replacing the drive belt.

SERVICE AND MAINTENANCE

Friction Wheel Removal

Procedure for removing the friction wheel for inspection or replacement.

SERVICE AND MAINTENANCE

Friction Wheel Reassembly

Steps for reassembling the friction wheel assembly.

MAINTENANCE SCHEDULE

Schedule of recommended maintenance tasks based on usage intervals.

OFF-SEASON STORAGE

Preparing Engine for Storage

Steps to prepare the engine for off-season storage.

Preparing Snow Thrower for Storage

Steps to prepare the snow thrower for off-season storage.

Storage Warnings

Important warnings regarding safe storage locations and conditions.

TROUBLESHOOTING

Engine Issues

Troubleshooting common engine problems like starting and running issues.

Performance Issues

Troubleshooting issues related to vibration, power, propulsion, and snow discharge.

Contact Information

Information on where to get further assistance and support.

PARTS LIST

Auger and Housing Parts Diagram

Exploded view diagram of auger and housing components.

PARTS LIST

Auger and Housing Parts List

Detailed part numbers and descriptions for auger and housing components.

PARTS LIST

Handle and Chute Parts Diagram

Exploded view diagram of handle and chute components.

PARTS LIST

Handle and Chute Parts List

Detailed part numbers and descriptions for handle and chute components.

PARTS LIST

Wheel and Drive Parts Diagram

Exploded view diagram of wheel and drive components.

PARTS LIST

Wheel and Drive Parts List

Detailed part numbers and descriptions for wheel and drive components.

PARTS LIST

Engine Parts Diagram

Exploded view diagram of engine components.

PARTS LIST

Engine Parts List

Detailed part numbers and descriptions for engine assemblies.

PARTS LIST

Engine Sub-Assemblies List

Detailed part numbers for engine sub-assemblies.

Emission Control System Warranty

Manufacturer's Warranty Coverage

Details on the scope and duration of the manufacturer's warranty.

Owner's Warranty Responsibilities

Owner's duties for maintaining warranty coverage and proper use.

Warranty Requirements

Specific requirements and conditions for warranty claims.

Emission Control System Warranty

General Emissions Warranty

Details on the general coverage for engine emission control systems.

Emissions Durability and Air Index

Emissions Compliance Period

Information on engine emission durability and compliance periods.

REPAIR PROTECTION AGREEMENT

Agreement Benefits and Service

Details on Repair Protection Agreement benefits and service scheduling.

Service and Support

Home Service Options

Information on in-home and carry-in repair services.

Protection Plan Purchase

Information on purchasing a product protection agreement.

Related product manuals

Craftsman 31AM2T6D799

56 pages

Craftsman 31AS63TF799

72 pages

Craftsman 31BS62EE799

56 pages

Craftsman C950-52119-3

62 pages

88830 - Professional 357 CC 30" 2 Stage Snow Thrower

22-INCH 4-CYCLE SNOW THROWER 247.885550

44 pages

Craftsman 31AM62EE799 User Manual

Table of Contents

Questions and Answers:

Craftsman 31AM62EE799 Specifications

Summary

Operator's Manual

CRAFTSMAN 24" SNOW THROWER

Model No. 247.88955

Important Safety Notice

WARRANTY STATEMENT

CRAFTSMAN LIMITED WARRANTY

PRODUCT SPECIFICATIONS

SAFETY INSTRUCTIONS

General Safety Warnings

CALIFORNIA PROPOSITION 65

Preparation and Training

SAFETY INSTRUCTIONS

Safe Gasoline Handling

Safe Operation Practices

SAFETY INSTRUCTIONS

Maintenance and Storage Safety

Engine Modification Warning

Spark Arrestor Information

SAFETY INSTRUCTIONS

SAFETY SYMBOLS

SAFETY LABELS

DANGER Labels

ASSEMBLY

Unpacking and Initial Assembly

Loose Parts Identification

ASSEMBLY

Chute Assembly and Control

ASSEMBLY

Setup and Adjustments

ASSEMBLY

Chute Angle Adjustment

Auger Control Adjustment

OPERATION

Controls Overview

OPERATION

Engine Controls

Drive and Auger Controls

Chute and Skid Shoe Controls

OPERATION

Pre-Start Procedures

OPERATION

Starting Procedures

Stopping and Engaging

REPLACING SHEAR PINS

SERVICE AND MAINTENANCE

Engine Maintenance

SERVICE AND MAINTENANCE

Spark Plug Maintenance

Gear Shaft Lubrication

SERVICE AND MAINTENANCE

Component Maintenance

Shave Plate and Skid Shoes

Cable Adjustments

SERVICE AND MAINTENANCE

Cable Adjustments (cont.)

Bracket Adjustments

Belt Replacement

SERVICE AND MAINTENANCE

Auger Belt Replacement

SERVICE AND MAINTENANCE

Auger Belt Replacement (cont.)

Drive Belt Replacement

SERVICE AND MAINTENANCE

Friction Wheel Removal

SERVICE AND MAINTENANCE

Friction Wheel Reassembly

MAINTENANCE SCHEDULE

OFF-SEASON STORAGE

Preparing Engine for Storage

Preparing Snow Thrower for Storage

Storage Warnings

TROUBLESHOOTING

Engine Issues

Performance Issues

Contact Information