Craftsman 31AS63TF799

Questions and Answers

C
cheryl52Aug 13, 2025
What to do if Craftsman 31AS63TF799 fails to discharge snow?
- C
  Connie ChanAug 13, 2025
  If your Craftsman Snow Blower isn't discharging snow, here's what might be happening and how to resolve it: * The chute assembly could be clogged. Stop the engine immediately, disconnect the spark plug wire, and clean the chute assembly and inside of the auger housing with a clean-out tool or a stick. * A foreign object might be lodged in the auger. Stop the engine immediately, disconnect the spark plug wire, and remove the object from the auger with a clean-out tool or a stick. * The auger cable may need adjustment. Adjust the auger control cable. Refer to Assembly section. * The auger belt might be loose or damaged. Replace the auger belt. Refer to Service and Maintenance section. * Shear pins might be sheared. Replace them with new ones.
J
Joseph EspinozaAug 17, 2025
Why is my Craftsman 31AS63TF799 Snow Blower engine running erratically?
- L
  Laura JohnsonAug 17, 2025
  If your Craftsman Snow Blower engine is running erratically with inconsistent RPM, it could be due to several reasons: * The engine might be running on CHOKE; move the choke control to the RUN position. * The fuel might be stale; fill the tank with clean, fresh gasoline. * There might be water or dirt in the fuel system; drain the fuel tank and refill with fresh fuel. * The engine might be over-governed. Contact your Sears Parts & Repair Center.
H
Heather AndersonAug 21, 2025
How to troubleshoot loss of power in Craftsman 31AS63TF799?
- D
  Dennis FosterAug 21, 2025
  If your Craftsman Snow Blower is losing power, check the following: * Ensure the spark plug wire is securely connected and tightened. * Make sure the gas cap vent hole isn't plugged; remove any ice and snow, and ensure the vent hole is clear.
J
James ParkerAug 26, 2025
What to do if Craftsman Snow Blower won't propel itself?
- S
  Shane JensenAug 26, 2025
  If your Craftsman Snow Blower isn't moving on its own, consider these potential issues: * The drive cable may need adjustment. Adjust the drive control cable. Refer to Service and Maintenance section. * The drive belt might be loose or damaged. Replace the drive belt. Refer to Service and Maintenance section. * The friction wheel could be worn. Change the friction wheel or contact your Sears Parts & Repair Center.
A
Allison JonesAug 30, 2025
Why does my Craftsman Snow Blower have excessive vibration?
- W
  wendy29Aug 30, 2025
  If your Craftsman Snow Blower is vibrating excessively, immediately stop the engine and disconnect the spark plug wire. Tighten all bolts and nuts. If the vibration continues, have the unit serviced by a Sears Parts & Repair Center.
R
Ross FryeSep 3, 2025
How to fix Craftsman 31AS63TF799 Snow Blower chute that won't rotate easily?
- B
  Brittany GonzalezSep 3, 2025
  If the chute on your Craftsman Snow Blower won't easily rotate 180 degrees, it might be assembled incorrectly. Unassemble the chute control and reassemble as directed in the Assembly section.
W
Whitney VaughnNov 7, 2025
Why my Craftsman 31AS63TF799 engine fails to start?
- T
  Travis KingNov 7, 2025
  If your Craftsman Snow Blower engine won't start, possible causes include: * The choke control might not be in the CHOKE position; if so, move it to the CHOKE position. * The spark plug wire might be disconnected; connect it to the spark plug. * The spark plug might be faulty; clean, adjust the gap, or replace it. * The fuel tank might be empty or contain stale fuel; fill the tank with clean, fresh gasoline. * The engine might not be primed; prime it as instructed in the Operation Section. * The key might not be inserted; insert the key fully into the switch. * The extension cord might not be connected (if your model has an electric start button); connect one end of the extension cord to the electric starter outlet and the other end to a three-prong 120-volt, grounded, AC ou...

Craftsman 31AS63TF799 Specifications

General

Throwing Distance	Up to 40 feet
Stages	Two-stage
Drive Type	Self-propelled
Auger Material	Steel
Engine	208cc OHV
Start Type	Electric Start
Number of Speeds	6 Forward / 2 Reverse
Wheel Size	13 in.
Intake Height	21 inches