EasyManua.ls Logo

Craftsman 919.725502 - User Manual

Craftsman 919.725502
48 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Owners Manual
Permanently Lubricated
2-Stage
Twin V
Portable
AIR COMPRESSOR
• Safety Guidelines
• Assembly
• Operation
• Maintenance
• Service and Adjustments
• Troubleshooting
• Repair Parts
Model No.
919.725502
CAUTION: Read the Safety Guidelines
and All Instructions Carefully Before
Operating.
Sold by Sears Canada, Inc. Toronto, Ont. M5B 2B8
A14123 Rev. 1 11/09/05

Table of Contents

Questions and Answers

  • E
    Erika MooreAug 16, 2025
    What to do if my Craftsman 919.725502 motor will not run?
    • C
      Cathy WarnerAug 16, 2025
      If your Craftsman Air Compressor motor won't run, several factors could be at play. First, the motor overload protection switch may have tripped; allow the motor to cool, and the switch will reset automatically. Ensure the tank pressure is below the pressure switch's cut-in point, as the motor restarts when pressure drops sufficiently. A blown fuse or tripped circuit breaker could also be the culprit. Also, consider these potential causes: using an incorrect extension cord, a stuck-open check valve, loose electrical connections, or a defective motor or starting capacitor.
  • H
    hloweryAug 19, 2025
    Why is my Craftsman Air Compressor not supplying enough air?
    • B
      Benjamin HardySep 12, 2025
      If your Craftsman Air Compressor isn't supplying enough air, first, reduce your air usage. Check the air requirements of your accessories. If the accessory requires a higher SCFM or pressure than your compressor provides, you'll need a larger compressor. The issue may also be caused by a hole in the hose, a restricted check valve, air leaks, or a restricted air intake filter.
  • C
    cassandra07Aug 22, 2025
    How to fix air leaks at the fittings of a Craftsman Air Compressor?
    • K
      Kristina BrownAug 22, 2025
      If you notice air leaks at the fittings of your Craftsman Air Compressor, start by tightening the fittings where you hear air escaping, but avoid overtightening. Using a soapy water solution can help you locate the leaks. If the leak persists even after tightening, the check valve seat may be damaged, resulting in a constant air leak at the pressure release valve when the compressor is off and the tank is pressurized. In this case, the check valve should be replaced.
  • S
    Savannah VillarrealAug 25, 2025
    What causes air leaks at the pressure switch release valve on a Craftsman 919.725502?
    • N
      Nicholas HodgeAug 26, 2025
      If your Craftsman Air Compressor has air leaks at the pressure switch release valve, this indicates a defective pressure switch release valve or a defective air tank. In this case, contact a Trained Service Technician. The air tank must be replaced; do not attempt to repair the leak.
  • B
    Benjamin GutierrezAug 28, 2025
    What to do if the safety valve pops off on my Craftsman Air Compressor?
    • R
      Richard HayesAug 28, 2025
      If the safety valve on your Craftsman Air Compressor pops off due to excessive tank pressure, immediately move the On/Auto/Off lever to the "OFF" position. If the unit does not shut off, it could indicate that the pressure switch isn't shutting off the motor when the compressor reaches its cut-out pressure, or that the pressure switch cut-out is set too high. In this situation, contact a Trained Service Technician.
  • D
    David FieldsAug 31, 2025
    Why is my Craftsman 919.725502 Air Compressor making a knocking noise?
    • A
      Alec GarzaAug 31, 2025
      If your Craftsman Air Compressor is making a knocking noise, it could be due to a defect in the safety valve or a defective check valve. Try manually operating the safety valve by pulling on its ring; if it continues to leak, replacement is necessary. Alternatively, remove and clean the check valve, or replace it if needed.
  • S
    sanchezmorganSep 3, 2025
    What to do if the pressure drops when using an accessory with my Craftsman 919.725502?
    • A
      Andrew KramerSep 3, 2025
      It's normal for some pressure drop to occur on the regulated pressure gauge of your Craftsman Air Compressor when an accessory is in use. However, if the pressure drop is excessive, adjust the regulator following the instructions in the "Description of Operation" paragraph in the "Operation Section."
  • J
    James AndersonSep 6, 2025
    Why does the regulator knob on my Craftsman 919.725502 have a continuous air leak?
    • K
      Karen RandallSep 6, 2025
      If the regulator knob on your Craftsman Air Compressor has a continuous air leak, the regulator is damaged and needs to be replaced.
  • W
    Whitney HunterSep 9, 2025
    What to do if the regulator on my Craftsman Air Compressor will not shut off air outlet?
    • A
      andrew64Sep 9, 2025
      If the regulator on your Craftsman Air Compressor will not shut off the air outlet, it means the regulator is damaged and needs to be replaced.
  • S
    Sabrina PayneSep 12, 2025
    What causes air leaks between the head and valve plate on a Craftsman 919.725502?
    • K
      Katherine AllenSep 12, 2025
      If there are air leaks between the head and valve plate of your Craftsman Air Compressor, it's due to a leaking seal. Contact a Trained Service Technician to address this issue.

Craftsman 919.725502 Specifications

General IconGeneral
Model Number919.725502
TypePortable
Power SourceElectric
Tank Capacity25 Gallons
Max Pressure150 PSI
Voltage120V
Amperage15 Amps
Pump TypeOil-Free
Weight110 lbs
CFM at 40 PSI6.8 SCFM

Related product manuals