To Next PageTo Next PageWhy is my Craftsman Lawn Mower engine overheating?
If your Craftsman Lawn Mower engine overheats, it could be due to: low engine oil level (fill the engine with the proper amount and type of oil) or restricted airflow (clean grass clippings and debris from around the engine’s cooling fins and blower housing).
Why is my Craftsman PRO 247.888740 Snow Blower experiencing excessive vibration?
If your Craftsman Snow Blower is vibrating excessively, immediately stop the engine and disconnect the spark plug wire. Tighten all bolts and nuts. If the vibration continues, have the unit serviced by a Sears Parts & Repair Center.
Why is my Craftsman Snow Blower not throwing snow?
If your Craftsman Snow Blower is not discharging snow, first, immediately stop the engine and disconnect the spark plug wire. Check the chute assembly for clogs and clean it, along with the inside of the auger housing, using a clean-out tool. Also, check for any foreign objects lodged in the auger and remove them with the clean-out tool. If these steps don't resolve the issue, the auger cable may need adjustment or the auger belt may be loose or damaged. In that case you should refer to the Assembly section or Service and Maintenance section. Another possibility is that the shear pins have sheared, requiring replacement; refer to the Operation section for instructions.
What to do if my Craftsman PRO 247.888740 won't move on its own?
If your Craftsman Snow Blower isn't propelling itself, the drive cable may need adjustment. You can adjust the drive control cable by referring to the Service and Maintenance section. Alternatively, the drive belt might be loose or damaged, requiring replacement, or the friction wheel may be worn, also requiring replacement. For both of these issues, refer to the Service and Maintenance section for guidance.
What to do if my Craftsman PRO 247.888740 Snow Blower has excessive vibration?
If your Craftsman Snow Blower is vibrating excessively, immediately stop the engine and disconnect the spark plug wire. Then, carefully tighten all bolts and nuts. If the vibration continues after doing this, it is recommended to have the unit serviced by a Sears Parts & Repair Center.
Why doesn't the chute on my Craftsman PRO 247.888740 Snow Blower easily rotate 180-200 degrees?
If the chute on your Craftsman Snow Blower doesn't easily rotate, it might be assembled incorrectly. Disassemble the chute control and reassemble it as directed in the Assembly section.
How to fix a Craftsman Snow Blower when the engine fails to start?
If your Craftsman Snow Blower engine won't start, check these potential causes: 1. Ensure the choke control is in the CHOKE position; if not, move it accordingly. 2. Verify the spark plug wire is connected; if disconnected, reconnect it. 3. Inspect the spark plug for faults; clean, adjust the gap, or replace it if necessary. 4. Check the fuel tank; if empty or the fuel is stale, fill it with fresh gasoline. 5. Prime the engine as described in the Operation section. 6. Make sure the safety key is fully inserted into the switch. 7. If using the electric start, ensure the extension cord is properly connected to both the snow blower and a grounded AC outlet.
What to do if Craftsman Lawn Mower engine fails to start with electric starter?
If your Craftsman Lawn Mower engine fails to start with the electric starter, consider the following: - Ensure the Electric Starter Push Key is fully inserted into the starter housing until it snaps into place. - The battery may not be charged. Charge the battery. - The circuit breaker might have tripped. Stop the engine, remove the Electric Starter Push Key, and disconnect the spark plug boot. Check for and carefully remove any debris obstructing the blade. Reattach the spark plug boot and reinsert the Electric Starter Push Key. Wait one minute for the circuit breaker to automatically reset, then try starting again.
Why Craftsman Lawn Mower engine fails to start?
The Craftsman Lawn Mower engine may fail to start due to several reasons: - The blade control might be disengaged, so ensure it is engaged. - The spark plug boot could be disconnected; check and connect it. - The fuel tank may be empty or contain stale fuel; refill with fresh gasoline. - The engine may not be primed; prime it as instructed in the Operation section. - The spark plug might be faulty; clean, adjust the gap, or replace it. - The engine could be flooded; wait a few minutes before restarting.
Why my Craftsman Lawn Mower engine fails to start?
If your Craftsman Lawn Mower engine won't start, possible causes include: the PTO/Blade Engage knob is engaged (place it in the disengaged/OFF position), the parking brake isn't engaged (engage it), the spark plug wire is disconnected (connect it), the throttle control lever isn't in the correct starting position (place the Throttle lever to FAST position), the fuel tank is empty or the fuel is stale (fill the tank with clean, fresh gas that is less than 30 days old), the fuel line or fuel filter is blocked (replace the fuel line; replace the fuel filter), the spark plug is faulty (clean, adjust the gap, or replace the plug), the engine is flooded (crank the engine with the throttle in FAST position), or a fuse is blown (replace the fuse).
General| Brand | Craftsman |
|---|---|
| Model | PRO 247.888740 |
| Category | Snow Blower |
| Language | English |
