Why won't my Craftsman WS405 Trimmer engine start?
Several factors can prevent your Craftsman Trimmer from starting. First, ensure the fuel tank isn't empty; if it is, refill it with fresh fuel. If the primer bulb wasn't pressed enough, press it 10 times. Old fuel (over 30 days) can also be the culprit, so drain the tank and add fresh fuel. Lastly, a fouled spark plug can cause this issue, so consider replacing it.
What to do if my Craftsman WS405 engine lacks power or stalls?
If your Craftsman Trimmer engine lacks power or stalls, the issue might be due to several reasons. Old fuel (over 30 days) can cause this, so drain the fuel tank and add fresh fuel. A dirty air filter can also be the cause; clean or replace it. Lastly, check the spark plug; if it's fouled, replace it.
How to fix a Craftsman Trimmer when the cutting head will not advance line?
If the cutting head on your Craftsman Trimmer won't advance the line, consider these possibilities: * The cutting head is bound with grass, stop the engine and clean the cutting head. * The cutting head is out of line, clean and thoroughly dry the cutting head. * The inner reel is bound up, clean the inner reel and outer spool. * The cutting head is dirty, stop the engine and clean the cutting head. * The line is welded, open the cutting head and remove the welded section. * The line is twisted, rewind the line. * Not enough line is extended, stop the unit, push the bump knob and pull the line until 4 inches (102 mm) is outside of the cutting head.
What to do if Craftsman WS405 Trimmer engine will not idle?
If your Craftsman Trimmer engine won't idle, it might be because of a dirty air filter, so clean or replace it. Another reason could be old fuel (over 30 days); in this case, drain the fuel tank and add fresh fuel. Finally, the idle speed might be incorrect; you should adjust the idle speed.
Why won't my Craftsman WS405 Trimmer engine accelerate?
If your Craftsman Trimmer engine won't accelerate, it could be due to a few reasons. Old fuel (over 30 days) can cause this, so drain the fuel tank and add fresh fuel. Another cause may be the cutting head is bound with grass, in which case you should stop the engine and clean the cutting head. Also, a dirty air filter can restrict performance; clean or replace it.
What causes the cutting line to advance uncontrollably on a Craftsman WS405 Trimmer?
If the cutting line on your Craftsman Trimmer advances uncontrollably, it is likely due to oil, cleaner, or lubricant in the cutting head. To resolve this, clean and thoroughly dry the cutting head.
General| Power Source | Gas |
|---|---|
| Cutting Width | 17 inches |
| Cutting Swath | 17 inches |
| Line Diameter | 0.095 inches |
| Shaft Type | Straight |
| Warranty | 2 years |
| Line Feed | Bump |
| Handle Type | Adjustable |
| Line Feed System | Bump Feed |
Information regarding spark arrestor requirements for specific locations and emissions.
Warning about chemicals in engine exhaust known to cause cancer or birth defects.
Emphasizes the necessity of reading and following all safety instructions before use.
Covers flammability, fueling precautions, and ventilation requirements for gasoline.
Details personal protective equipment and safe operating practices during use.
Covers maintenance, safety device integrity, and proper storage procedures.
Explains symbols like Safety Alert, Read Manual, Primer Bulb, and E85 Fuel warning.
Covers mandatory eye, hearing, foot, and hand protection for safe operation.
Warns about thrown objects, hot surfaces, sharp blades, and improper cutting head modifications.
Advises keeping bystanders away and ensuring proper handle positioning.
Lists the primary uses of the trimmer, such as cutting grass and edging.
Lists the tools needed for assembly, primarily a flat-head screwdriver.
Provides key technical data like engine displacement, spark plug gap, and cutting path diameter.
Step-by-step guide to properly attach the cutting head shield for safety.
Instructions on how to connect and disconnect various attachments using the coupler.
Details how to install and adjust the handle for comfortable and secure operation.
Guide for attaching and adjusting the optional shoulder strap for better support.
Specifies using high-quality SAE 30 weight oil and avoiding dirty oil.
Instructions for adding the correct amount of oil before the first use.
Advises using fresh, clean unleaded gasoline and warns against E85 fuel.
Provides detailed safety precautions and steps for safely fueling the unit.
Step-by-step guide to start the engine, including primer bulb and throttle usage.
Procedures for safely shutting down the engine using the On/Off switch.
Instructions on correct body posture, grip, and unit positioning for safe operation.
Explains how to release more trimming line using the bump head while operating.
Provides advice on cutting techniques, direction, and handling different grass conditions.
Describes the technique for trimming around trees, posts, and fences at a 30° angle.
Details how to use the trimmer attachment for edging tasks, including rotating the head.
Outlines the required maintenance tasks and their frequencies (e.g., air filter, oil change).
Step-by-step instructions for installing new trimming line into the cutting head.
Guide to removing old line and clearing any obstructions from the cutting head.
Explains how to check the engine oil level before each use.
Provides instructions for draining and refilling the engine oil.
Details the process for cleaning and re-oiling the air filter.
Instructions on how to adjust the idle speed for smooth engine operation.
Covers checking, cleaning, gapping, and replacing the spark plug.
Provides guidance on cleaning the exterior of the unit without damaging plastic parts.
Covers safe storage practices for both short-term and long-term periods.
Addresses problems like engine not starting, idling, accelerating, or stalling.
Covers problems with line advancement and uncontrollable line movement.
Covers warranty period, defects, and what is not covered.
Details requirements for qualifying and obtaining warranty service.
Lists responsibilities MTD LLC disclaims, such as loss of time or transportation costs.
Outlines limitations on implied warranties and liability for incidental damages.
Explains how state law may grant additional rights beyond the limited warranty.
To Next Page