Page 18 of 29
*”Select Block 1" - BLOCK SELECTION BANK 1 ROUTINE (Config 2 must be enabled – Config 2 1)
This function is used to set selections which will be blocked during certain periods of the day. Press key number 4 will
enter “Enable X”.
“Enable X” - Blocking Enable Routine
This function is used to disable blocking “Enable 0” or enable blocking “Enable 1”. When enabled, active selections
will not be allowed to vend on the days and times programmed. Press key number 4 and the current “Enable” setting
will be displayed. Press key number 2 or 3 to scroll between “Enable 0” and “Enable 1”. Press key number 4 with the
display blinking the setting you wish to use. Display will return to “Enable X”. Press key number 2 to scroll to “Start
Time”.
“Start Time” - Start Selection Blocking Routine
This function is used to set the day(s) and time to start selection blocking. Press key number 4 and “Start Day” will show
on the display.
“Start Day” - Day of Week Start Setting
This function is used to set the day(s) of the week to start selection blocking. Press key number 4 and “XXXXXX#”
will show on the display, where XXXXXX will be the day of the week (i.e. Monday, Tuesday, Wednesday, Thursday,
Friday, Saturday, Sunday, Every day) and # is 0 = disable, 1 = enable. With the display showing the day you wish to
set press key number 4. The # will start blinking. Press key number 2 or 3 to scroll between “XXXXXX0” and
“XXXXXX1.” Press key number 4 with the display showing the setting you wish to use. Display will return to
“XXXXXX#’. Press key number 2 to scroll to the next day to set or press key number 1 to return to “Start Day”. Press
key number 2 to scroll to “Start Hour”.
“Start Hour” - Start Hour and Minute Setting
This function is used to set the hours and minutes to start selection blocking. Press key number 4 and “hhmm” will
show on the display, where hh is the hour (military time) and mm is the minute. “hh” will be blinking, indicating the
hour setting may be changed. Press key number 2 to scroll from 00 to 23. With the display showing the hour you
wish to start selection blocking, press key number 4. “mm” will then start blinking, indicating the minute setting may
be changed. Press key number 2 to scroll from 00 to 59. With the display showing the minute you wish to start
selection blocking, press key number 4. The display will return to “Hour”. Press key number 1 to return to “Start
Time”. Press key number 2 to scroll to “Stop Time”.
“Stop Time” - Stop Selection Blocking Routine
This function is used to set the day(s) and times to stop selection blocking. Press key number 4 and “Stop Day” will show
on the display.
“Stop Day” - Day of Week Stop Setting
This function is used to set the days of the week to stop selection blocking and can be set in the same manner
as Day of Week Start Setting.
“Stop Hour” - Stop Hour and Minute Setting
This function is used to set the hours and minutes to stop selection blocking and can be set in the same manner
as Start Hour and Minute Setting.
Press key number 1 to return to “Stop Time”.
Press key number 2 to scroll to “Selection”.
“Selection” - Selection to Be Affected By Blocking
This function is used to set selection(s) which will be blocked during certain periods of the day. Press key number
4 and “Select A1 #” will be displayed, where # is the current setting for the selection number displayed. 0 = disabled;
1 = enabled. Press key number 2 to scroll to the key number setting you desire to change. Press key number 4
with the key number showing you wish to change (i.e. Select A1 #) and the # will start blinking. Press key number
2 or 3 to scroll between Select A1 0 and Select A1 1. Press key number 4 with the display showing the setting you
wish to use. Display will return to Select A1 #. Press key number 1 to return to “Selection”. Press key number 2 to
scroll to “Lighting #”.
To Next Page
Loading...
Need help?
General
