Page 20 of 29
“Stop Time” - Stop Discount Pricing
This function is used to set the day(s) and times to stop discount prices. Press key number 4 and “Stop Day” will
show on the display.
“Stop Day” - Day to Stop Setting
Set this feature using instructions for “Select Block 1”, “Stop Time”, “Stop Day”.
“Hour” - Stop Hour and Minute Setting
Set this function using instructions for “Select Block 1”, “Stop Time”, “Stop Hour”.
“Selection” - Selection Affected by Discount Pricing
This function is used to set selection(s) which will be affected by discount prices. Press key number 4 and “Select A1
#” will be displayed, where # is the current setting for the selection number displayed. 0 = disabled, 1 = enabled.
Press key number 2 to scroll to the key number you desire to change.
Press key number 4 with the key number showing you wish to change (i.e. Select A1 #) and the # will start blinking.
Press key number 2 or 3 to scroll between “Select A1 0” and “Select A1 1”. Press key number 4 with the display
showing the setting you wish to use. Display will return to “Select A1 1”. Press key number 1 to return to
“Selection”. Press key number 2 to scroll to “Less Amount”.
“Less Amount” - Discount Amount (Price)
This function is used to set the discount amount (price) for selection(s) and times set. Press key number 4 and “##.##”
will be displayed, where “##.##” is the current discount price that is set. Press key number 2 or 3 to change the price
(00.00 to 99.99). Press key number 4 with the display showing the price setting you wish to use. Display will show
price. Press key number 1 to return to “Less Amount”. Press key number 1 to return to “Select Discount”. Press key
number 2 to scroll to “Health Setting”.
Health Safety” – HEALTH SETTING ROUTINE
This function is used to enable the health protection feature for product when needed. When enabled it operates as
follows:
1. Cabinet temperature must be maintained at 41º F (5º C) or below for product to be vended while in normal
operation. If the cabinet temperature exceeds 41º F, and fails to return to 41º F or below for 15 minutes the
controller will issue a “Health Code” error and disable vending of health protected products.
2. After door closure, (refill or service) the machine has 30 minutes to pull down to 45º F (7º C). If the machine has
not reached 45º F (7º C) after 30 minutes the controller will issue a “Health Timer” error. Once a health time error
is activated the controller will not allow product to be delivered. After 30 minutes if the temperature is 45º F or
less, but not 41º F the controller will set a 15 minute timer. During this time, if the cabinet temperature falls below
41º F (5º C) the controller will allow health guarded product to be delivered. If the temperature doesn’t fall below
41º F (5º C) the controller will issue a “Health Code” error and disable vending of health protected products.
3. Power loss for 30 minutes or longer will result in automatic “Health Code” error activation and disable vending
of health protected products upon power up.
4. Power loss less than 30 minutes. Once the machine regains power, if the cabinet temperature is 45º F (7º C) or less
the controller will allow product to be dispensed. The controller will allow an additional 15 minutes for the
temperature to pull down to 41º F (5º C). If the temperature doesn’t reach 41º F (5º C) or less after the 15 minute
period the controller will issue a “Health Code” error and disable vending of health protected products. If the
temperature is greater than 45º F (7º C) on power up the controller will automatically set a “Health Code” error
and disable vending of health protected products.
5. Power loss less than 15 minutes. On power up the controller will allow vending. If the cabinet temperature
doesn’t reach 41º F (5º C) or less in 15 minutes the controller will issue a “Health Code” error and disable
vending of health protected products.
To enable, with “Health Setting” on display press key number 4 will enter “Enable #”.
“Enable #” – Health Enable Routine
This function is used to enable the Health Protection feature. When enabled, protected selections will only be
allowed to vend if health constraints listed above are met. Press key number 4 and the current “Enable” setting will
be displayed. Press key number 2 or 3 to scroll between “Enable 0” and “Enable 1”. Press key number 4 with the
display blinking the setting you wish to use. Display will return to “Enable #”. Press key number 2 to scroll to
“SELECT”.
To Next Page
Loading...
Need help?
General
