Page 21 of 29
“Selection” – Selection(s) To Be Affected By Health Protection
This function is used to set selection(s) which will be protected by the Health Protection constraints. Press key
number 4 and “All Selections” will be displayed. Press key number 2 to scroll through “All Selections, A, B, C, D, and
E”. Press key number 4 with the setting you wish to enter. Selecting “A, B, C, D, or E” will allow you to choose
settings for that tray. Example: With “A” showing on display press key number 4. Display will show “All Selections
#”, press key number 2 to scroll through “A All Selections #, Select A1 #, Select A2 #, Select A3 #, etc… With the
setting you wish to change press key number 4 and the # will start blinking. Press key number 2 to scroll between
“0” disabled and “1” enabled. With the setting you wish to use showing on the display press key number 4. Display
will return to “A All Selections # or Select A# #”. Press key number 1 to return to “Selection”. Press key number 1
to return to “Health Safety”. Press key number 2 to scroll to “Over-ride Switch”
“Over-ride Switch” - MANUAL SWITCH OVERRIDE ROUTINE
This function is used to allow a key switch to override some of the settings stored for normal operations. This function
can be programmed to control one or several of the following features: Free Vend Enable, Selection Blocking, Discount
Pricing, and Lighting Control. Press key number 4 and the display will show “Free Vend #”. Press key number 2 or 3 to
scroll through the override routines available. Press key number 1 to return to “Over-ride Switch”.
“Free Vend #” - Free Vend Enable Routine
This function is used to set the vender to free vend. 0 = disable, 1 = enable. Press key number 4 and “#” will start
flashing. Press key number 2 or 3 to scroll between “Free Vend 0” and “Free Vend 1”. Press key number 4 with
the display blinking the setting you wish to use. Display will return to “Free Vend #”. Press key number 2 to scroll
to “No Vend #”.
“No Vend #” - No Vend (Vend Override) Enable Routing
This function is used to set vender selections to not be allowed to vend and a “No sales available” message
to be displayed. 0 = disable, 1 = enable. Press key number 4 and “#” will start flashing. Press key number 2
or 3 to scroll between No Vend 0 and No Vend 1. Press key number 4 with the display showing the setting
you wish to use. Display will return to “No Vend #”. Press key number 2 to scroll to “Sales Block #”.
“Sales Block #” - Selection Blocking Override Routine
This function is used to override “Select Block 1” and “Select Block 2” if they are being used. “Sales Block 0” is
disabled, “Sales Block 1” is enabled. Press key number 4 and “#” will start flashing. Press key number 2 or 3 to
scroll between “Sales Block 0” and “Sales Block 1”. Press key number 4 with the display blinking the setting
you wish to use. Display will return to “Sales Block #”. Press key number 2 to scroll to “Discount #”.
“Discount #” - Discounting Override Routine
This function is used to override “Select Discount” if it is being used. “Discount 0” is disabled and “Discount 1”
is enabled.
Press key number 4 and “#” will start flashing.
Press key number 2 or 3 to scroll between “Discount 0” and “Discount 1”. Press key number 4 with the display
showing the setting you wish to use. Display will return to “Discount #”. Press key number 2 to scroll to “Lighting
#”.
“Lighting #” - Lighting Control Override Routine
This function is used to override “Lighting Control” if it is being used. “Lighting 0” is disabled and “Lighting 1”
is enabled.
Press key number 4 and “#” will start flashing.
Press key number 2 or 3 to scroll between “Lighting 0” and “Lighting 1”. Press key number 4 with the display
blinking the setting you wish to use. Display will return to “Lighting #”. Press key number 2 to scroll to
“Refrigeration #”.
“Refrigeration #” - Refrigeration Control Override Routine
This function is used to override “Refrigeration”, if it is being used. “Refrigeration 0” = disabled and “Refrigeration
1” = enabled. Press key number 4 and “#” will start flashing. Press key number 2 or 3 to scroll between
“Refrigeration 0” and “Refrigeration 1”. Press key number 4 with the display showing the setting you wish to use.
Display will return to “Refrigeration #”. Press key number 1 to return to “Over-ride Switch”. Press key number 2
to scroll to “Remote Vend Mech”.
To Next Page
Loading...
Need help?
General
