quickstart guide
TST-600
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TST-600
5.7” Wireless Touch Screen
1
Battery Switch
3
Basic Wireless Setup
QUICKSTART DOC. 7381E (2034457, Sheet 1 of 2) 09.14
1
2
Configure the Touch Screen
The TST-600 from Crestron
®
ships with the battery switch (on the rear) in the
OFF (downward) position. The OFF position is used for shipping and long
term storage only. Use the included T-pin to turn the switch ON (slide it
upward) and place the TST-600 on the included docking station/charger for a
minimum of four hours before using.
To charge the internal battery, the TST-600 must be placed on the
TST-600-DS Docking Station, which must be connected to a powered
TST-600-IMCW Interface Module (included).
The main menu is the starting point for configuring the TST-600. If no project is
loaded, touch the screen to access the main menu. If a project is running, the
main menu can be accessed by using the following procedure:
1. Press and hold the left trigger key on the top of the touch screen until the unit
resets (approximately 5 seconds).
2. When the display turns black, then displays a “3”, release the trigger key.
3. When “Loading Crestron Applications” appears on the display, touch the
screen.
4. Release the touch screen when “Preparing to enter setup” appears.
The main menu can also be accessed by pressing HOME, MEDIA, and, on
the left of the touch screen display, in sequence twice (press HOME, MEDIA, ,
, HOME, MEDIA, , ) within a 5 second period.
NOTE: From any of the setup menus, touch to go back to the previous menu.
Before a TST-600 can be used with a Crestron control system, it must first be acquired by a CEN(I)-ERFGW-POE Extended Range RF Wireless
Gateway (sold separately).
To acquire a TST-600:
1. Use a stylus or other thin tipped object to press ACQUIRE on the CEN(I)-ERFGW-POE gateway to enter Acquire mode. The accompanying
LED illuminates, indicating the unit is ready to link with the touch screen.
2. From the main menu on the TST-600, touch RF Setup to display the RF Setup screen. Then place the TST-600 in Acquire mode by touching
Acquire on the RF Setup screen. The screen displays an “Acquire in progress” message and the TST-600 is automatically acquired by the
gateway within 2 minutes.
3. When the process is complete, the screen displays an “Acquire OK” message. Press ACQUIRE on the gateway to exit Acquire mode. The LED
turns off.
NOTE: Select an RF channel between 12 and 23 for maximum range. Channels 11, 24-26 will result in less
range but are available if RF interference requires moving the RF channel.
For details, refer to “Appendix A: The RF Spectrum” and “Appendix B: Optimum RF Reception Guidelines” in
the TST-600 Configuration Guide (Doc. 7383).
For regulatory compliance information, refer to Doc. 7382.
NOTE: The RF ID of the unit must match the RF ID specified in the SIMPL Windows program.
Up
Channel 11
(802.11b/g)
Channel 6
(802.11b/g)
Channel 1
(802.11b/g)
Channel
11
12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
22 MHz
2 MHz
2483.5 MHz
2480
2462 MHz
2465 2470 247524602445 2450 24552440
2437 MHz
243524302425242024152410
2412 MHz2400 MHz
Wi-Fi (802.11b/g)
RF (802.15.4)
RF Setup Screen RF Setup (Acquire in Progress) Screen RF Setup (Acquire OK) Screen
For details on configuring the TST-600, refer to the TST-600 Configuration Guide
(Doc. 7383) at
www.crestron.com/manuals.
IEEE 802.15.4 Channel Selection (2400 MHz PHY)
To Next Page
Need help?
General
