76
allow children to handle blades. Blades and other small
parts are choking hazards and should be kept and
stored away from children.
Do not open, modify or otherwise tamper with Machine.
Do not operate if Machine or cord is damaged. Contact
Cricut Member Care for service:
cricut.com/contact or 1-877-727-4288.
Only use Cricut-approved power adapters. Always turn
Machine OFF before unplugging from the electrical
outlet. Never pull on the cord to disconnect Machine
from the electrical outlet; instead, grasp the plug and
pull to disconnect Machine.
The power cord should be positioned so that it will not
drape over the countertop or tabletop where it can
be tripped over, snagged or pulled on unintentionally
(especially by children).
Place Machine on a strong, flat, level and stable
surface. Make sure your work space has enough space
in the front and back of Machine to allow the cutting
mat to move through Machine freely.
Do not place your fingers or other objects in Machine
while connected to electrical power or while Machine is
powered on, or during cutting operations.
Keep hair, jewelry, loose clothing, fingers, other body
parts and any other items that could get caught in the
moving parts away from Machine while it is operating
as the rapid movements of the cutting carriage, mat
and material during operation may cause injury.
Do not touch the mat or material during cutting, even if
the mat or material stops moving. Do not touch the mat
or material until Machine ejects the mat or material
from Machine.
Machine should never be left or stored outside,
in unheated or unairconditioned spaces, or in
environments where Machine can come in contact
with water.
LIMITED WARRANTY: See cricut.com/warranty,
or write to manufacturer or authorized region
representative at applicable address shown,
for full terms and conditions.
Technical specications
Cricut Maker™ 4 Models: CXPL303, CXPL303A,
CXPL303B, CXPL303C
Description: The Cricut Maker™ 4 is a desktop
manufacturing device for helping do it yourself (DIY)
crafters make crafting projects. It takes images created
in a software design environment and recreates the
images in fabric, leather, paper and soft woods using
tools to cut, score, draw, transfer, perforate, engrave
and write on these materials.
The overall design is similar to a desktop printer or
plotter with an electrically driven head that moves the
design tools laterally and feed rollers that move the
crafting materials longitudinally. The combination of
these movements gives 2 axis motion to perform the
desired actions (cutting, drawing, etc.) on the crafting
materials in a 2 dimensional flat plane.
Every project is unique.
For more help resources, see
help.cricut.com
• Get inspiration and step-by-step tutorials on
youtube.com/cricut
• Join other Cricut Community members in our
ocial Cricut Facebook group
• Cricut Member Care: cricut.com/contact
or 1-877-727-4288
FCC STATEMENT
The U.S. Federal Communications Commission (in 47
CFR 15.105) has specied that the following notices be
brought to the aention of users of this product.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Pursuant to Part 15.21 of the FCC Rules, any changes or
modications to this equipment not expressly approved
by Cricut may cause harmful interference and void the
FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV
technician for help
Product specifications
Size 22.1 in x 7.1 in x 6.2 in (56 cm x 18.3 cm x 15.8 cm)
Weight 15.4 lbs (6.99 kg)
Power input (appliance inlet) 24.0 V 1.5 A
External power supply Model: TS-A066-2402751
Input: 100-240 V
~ 50/60 Hz 1.6 A
Output: 24.0 V 2.75 A
Model: PS66A240Y2750S
Input: 100-240 V ~ 50/60 Hz 1.6 A
Output: 24.0 V 2.75 A
Model: TS-A036-2401506
Input: 100-240 V ~ 50/60 Hz 1.2 A
Output: 24.0 V 1.5 A
Operating mode Continuous
Electrical classification Class III (Supplied by SELV)
Pollution degree PD 2
Ingress protection IPX0 (ordinary)
Wireless specifications
Transmission type Bluetooth®
Frequency Band 2.4000–2.4835 GHz
Maximum Radiated Power <= 100 mW (e.i.r.p.)
To Next Page
Loading...
