Crown ce 4000 - CE4000 Amplifi er Assembly

CE 4000 Service Manual
Parts 5-2
130485-1 Rev. B
©2002 Crown Audio, Inc.
5.3.1 CE4000 Amplifi er Assembly
Item Quantity Description Part # (CPN)
28 1 ASM, CE4000 BACK PANEL See section 5.2.2
27 1 ASM, CE4000 POWER SWITCH See section 5.2.8
26 1 COVER, CE4000 TOP PC 126223-4
25 3 4” CABLE TIE C 1811-1-6
24 1 8-32 HEX NUT W/BELLE A11056-2
23 2 TIE, 5.625” CABLE 127330-1
22 1 SUB-FRONT, CE4000 FP PC 130526-1
21 7 CAP, CE400 PEM STANDOFF 128119-2
20 1 PWA, CE4000 MAIN See section 5.4
19 1 INDUCTOR,PFC 127399-6
18 1 PWA, CE4000 FLYBACK See section 5.4
17 2 RIVET, CE4000 INS RET PLASTIC 128130-1
16 2 INSULATOR, CE4000 HS NOMEX 126923-4
15 1 COILS, CE4000 L/PLN MATCHED 127401-3
14 7 WASHER, CE4000 HEATSINK SHLDR 128120-1
13 7 #10 BELLVILLE WASHER SS A10098-4
12 7 MSCREW, 10-32 X 3.50 TORX PNHD Z 128345-1
11 2 RIVET, CE4000 FAN PLENUM SNAP 127777-1
10 1 PLENUM, CE4000 FAN 127473-3
9 4 6-32 HEX NUT W/BELLE A11056-1
8 16 SCREW, #6 X .250 MACH TORX PNHD 103436-70604
7 2 .5 X .136 X .02 NYLON WASHER A10101-5
6 1 SHEILD, CE4000 MAIN BD RBN AP 128218-7
5 1 PWA, CE4000 BFG See section 5.4
4 16 SEMS, 6-32 X .31 TORX PNHD STAR 103433-70605
3 10 8-32 X .31 SERR FLTHD T15 BZ 102156-1
2 2 KNOB, D350 D 8959-5
1 1 CHASSIS, CE4000 WELD/AP/PC 126222-11
NOTES:
1) THESE 8 SCREWS ARE USED TO FASTEN INPUT
AND OUTPUT MODULES TO BACK PANEL.
2) THESE 4 NUTS ARE USED TO FASTEN OUTPUT
MODULE BUSS BARS TO MAIN PWA.
3) SLIDE CABLE TIES (ITEM 25) THRU LANCES
IN CHASSIS, PLACE RIBBON CABLE (PART OF
ITEM 5) AGAINST CHASSIS SIDE PANEL BETWEEN
LANCES, THEN SECURE CABLE TIES AROUND
RIBBON CABLE.
RECOMMENDED ASSEMBLY TORQUES
ITEM NO. C.P.N. TORQUE SETTINGS
3 102156-1 12-14 IN LBS.
4 103433-70605 16-18 IN LBS.
8 103436-70604 10-12 IN LBS.
9 A11056-1 10-12 IN LBS.
12 128345-1 16-18 IN LBS
24 A11056-2 10-12 INLBS
ASM, NUMBER:
127390-4
Refer to Figure 5.1 for Exploded View