EasyManuals Logo

Cub Cadet LTX 1046 User Manual

Cub Cadet LTX 1046
36 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #29 background imageLoading...
Page #29 background image
Problem Cause Remedy
Engine fails to start 
2.
Spark plug wire(s) disconnected. 
Throttle/Choke control lever not in correct 4.
starting position.
Choke not activated 5.
Fuel tank empty, or stale fuel. 6.
Blocked fuel line. 7.
Faulty spark plug(s). 8.
Engine flooded. 9.

Engage parking brake. 2.
Connect wire(s) to spark plug(s). 
4.
position.
5.
the Choke position.
6.
old) gas.
Clean fuel line and replace fuel filter. 7.
Clean, adjust gap or replace plug(s). 8.
Crank engine with throttle in FAST position. 9.
Engine runs erratic  
Spark plug wire(s) loose. 2.
Blocked fuel line or stale fuel. 
Vent in gas cap plugged. 4.
Water or dirt in fuel system. 5.
Dirty air cleaner. 6.
Move the Throttle/Choke control lever out of 
the choke position.
Connect spark plug wire(s). 2.
Clean fuel line; fill tank with clean, fresh 
gasoline and replace fuel filter.
Clear vent or replace cap if damaged. 4.
Drain fuel tank. Refill with clean, fresh 5.
gasoline.
Replace air cleaner paper element or clean 6.
foam pre-cleaner.
Engine overheats Engine oil level low. 
Air flow restricted. 2.
Fill crankcase with proper amount and 
weight of oil.
Clean grass clippings and debris from around 2.

Engine hesitates at high

Spark plug(s) gap too close.  Remove spark plug(s) and reset the gap. 
Engine Idles rough Spark plug(s) fouled, faulty or gap too wide. 
Dirty air cleaner. 2.
Replace spark plug(s). Set plug gap. 
Replace air cleaner element and/or clean 2.
pre-cleaner.
Excessive vibration Cutting blade loose or unbalanced. 
Damaged or bent cutting blade. 2.
Tighten blade and spindle. 
Replace blade. 2.
Mower will not mulch grass Engine speed too low. 
Wet grass. 2.
Excessively high grass. 
Dull blade. 4.

position.
Do not mulch when grass is wet. 2.
Mow once at a high cutting height, then 
mow again at desired height or make a
narrower cutting swath.
Sharpen or replace blade. 4.
Uneven cut Deck not leveled properly. 
Dull blade. 2.
Uneven tire pressure. 

Sharpen or replace blade. 2.
Check tire pressure in all four tires. 
Troubleshooting
8
29

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cub Cadet LTX 1046 and is the answer not in the manual?

Cub Cadet LTX 1046 Specifications

General IconGeneral
Horsepower22 HP
Cutting Width46 inches
TransmissionHydrostatic
Deck MaterialSteel
Engine Displacement725 cc
Cylinders2
Cutting Height1.5 - 4 inches
Number of Blades2
Turning Radius18 inches
Front Tires15 x 6 inches
Rear Tires20 x 8 inches
Engine Power22 HP
Speed5.5 mph
EngineKohler Courage
Engine TypeFour-Cycle
Blade EngagementManual
Warranty3 years limited

Related product manuals