Curt Manufacturing 12070 - User Manual

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing Inc. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing Inc. may repair or replace
the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement
of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
MAKE: STYLE:
MIN.
30
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS: INSTALLATION TIME:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY:
MODERATE
EASY
MODERATE
HARD
THE INSTALL TIME LISTED IS FOR PROFESSIONAL
INSTALLERS. IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be
worn at all times while
installing this product
.
YEARS:
2010-PRESENT
CADILLAC
MODEL:
SRX
CROSSOVER
WARNING:
WE STRONGLY RECOMMEND THE USE OF AUXILIARY STABILIZING STRAPS FOR ALL
NON-TRAILER (WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US
ONLINE AT WWW.CURTMFG.COM FOR FURTHER INFORMATION.
3,500
350
TRAILER WEIGHT:
TONGUE WEIGHT:
12070 INSTALLATION INSTRUCTIONS
LBS.
LBS.
12/01/2009
TORQUE
WRENCH
RATCHET
SOCKET
10mm
19mm
SCREW
DRIVER
PART REMOVAL
WIRE PIPE
BRUSH
NO DRILLING REQUIRED
REMOVE CENTER FASCIA PANEL
AND RETURN TO OWNER
MASKING
TAPE
MAY REQUIRE WELDNUT
CLEANING

Summary

General Vehicle and Towing Specifications

Weight Carrying Capacity

Specifies the maximum trailer and tongue weight for the hitch installation.

Installation Time and Difficulty

Provides estimated installation time and the overall difficulty level of the process.

Required Tools and Preparation

Lists the necessary tools and provides essential tips for a successful installation.

Installation Walkthrough

Parts List and Initial Steps

Details the components required and the initial steps for removing the fascia panel.

Fascia Panel and Support Bracket Removal

Instructions for removing the rear fascia and associated support brackets.

Hitch Mounting and Fastening

Guidance on positioning the hitch and securing it with bolts and washers.

Reassembly and Final Torque

Steps for reinstalling the fascia support brackets and torquing all fasteners.

Completion of Installation

Final steps to complete the hitch installation and return components.

Important Safety and Maintenance Notes

Weldnut Cleaning Procedure

Instructions for cleaning debris from weldnuts prior to installation.

Periodic Hitch Inspection

Recommendation to regularly check fasteners and structural integrity of the hitch.

Warranty Information

Details on the product warranty, limitations, and conditions for repair or replacement.

Curt Manufacturing 12070 Specifications

General

Brand	Curt Manufacturing
Part Number	12070
Material	Steel
Hitch Class	Class 2
Country of Manufacture	USA
Finish	Black Powder Coat
Hitch Tube Size	1 1/4 in
Receiver Size	1-1/4 inch