Curtis D1000GT12A000 User Manual

Programming Options
4FFUIFmSTUQBHFPGUIFQSPHSBNNJOHHVJEFGPSJOTUSVDUJPOTPOBDDFTTJOHFBDIJOEJWJEVBMNFOVJUFN
Some menus save and exit automatically when a parameter is updated. Other menus exit to the previous menu
when a parameter is saved. To exit, press Źuntil EXIT appears on the display, then press
~.
Brew by Volume - adjusts the volume brewed (the factory default is 74 oz (2.2L). With an empty airpot in
place, press the appropriate BREW button. When the desired volume is reached, press the same BREW
button again to stop the brew cycle and set the volume.
Brew by Time - adjusts the amount of coffee brewed by time rather than by volume (the factory default is
3min-0sec). Once accessed, press Ż or ŹVOUJMUIFOVNCFSPGNJOVUFTJTnBTIJOH5IFOQSFTT
~ repeatedly
to change the number value. Press Ż or ŹVOUJMUIFOVNCFSPGTFDPOETJTnBTIJOH5IFOQSFTT~ repeatedly
to change the number value. Press Ż or ŹVOUJMiFYwJTnBTIJOHUIFOQSFTT
~ to exit.
Temperature - sets the brewing temperature of the water held in the water tank (the factory default is 200ºF).
The range is 170ºF to 206ºF. Once accessed, press Ż or Ź to choose the desired temperature. Then press ~
to set and exit.
Energy Save Mode - saves energy during periods when the brewer is not in use (the factory default is
OFF). When set to ON, the brewer automatically shuts off two hours after the last brew cycle. Press the ON/
OFF button to return to normal operation. When set to ON 140ºF, the brewer shuts off two hours after the last
brew cycle, but the water tank temperature remains at 140ºF. Use the ON 140ºF setting to reach brewing
temperature faster after periods of non-use. Once accessed, press Ż or Ź to choose the desired setting.
Then press
~ to set and exit.
Brew Count Odom - When accessed, this feature displays the total brew cycles since the odometer was last
reset. Press Ż to exit or ~ reset and exit.
Pre-Infusion - sets the brewer Pre-Infusion time (Pulse Brew must be off to access, the factory default is
Disabled). Pre-Infusion increases control of coffee clarity and extraction. When turned on, the range is 10 to 60
seconds. Once accessed, press Ż or Ź to choose the desired setting, then, press ~ to exit. To turn off pulse
brew mode, choose 0 for the time.
When Pre-infusion is ON, Pulse Brew disappears from the list of menu items.
Brew Count Total - when accessed, displays the total brew cycles on the brewer. It cannot be reset. The
display returns to the previous screen automatically after a few seconds.
Cold Brew Lock - adjusts the temperature at which the brewer will brew coffee when the BREW button is
pressed (Ready to Brew appears on the display, the factory default is 5ºF). This feature also adjusts the
temperature at which the heating element turns on to reheat the water in the tank. The available settings
are 5°F, 15°F and OFF. OFF is within 30°F below the temperature setting. Once accessed, press Ż or Ź to
choose the desired setting. Then press
~ to set and exit.
Master Reset - resets the brewer universal control module (UCM) to the factory default settings. Once
accessed, “Are You Sure?” will appear on the display. Press Ż for Yes or Ź for No.
Service Call - sets the service phone number that appears on the display when the UCM detects a SENSOR
ERROR or WATER ERROR . Once accessed, press Ż or Ź to choose the number to be changed. Then press
~ repeatedly to change the number value. Press Ż or Ź to choose the next number to change or choose exit
and press ~.
PROGRAMMING GUIDE PG8
WC-785/WC-789, PROGRAMMING GUIDE 050217NC

Curtis D1000GT12A000 Specifications

General

Brand	Curtis
Model	D1000GT12A000
Category	Coffee Maker
Language	English